manualshive.com logo in svg

Hiniker 1852, Operator'S Manual, Page: 23 / 31

Share
Download
Hiniker 1852 Operator'S Manual Download Page 23

V-Plow Assembly  21

22.  Check  that  the  plow  blade  is  level  on  the 

ground with the wings in the scoop position 

and the plow on the ground.

DWG NO. 3847

 

Level the plow by first loosening the jam nut 

on  the  stop  bolt  at  the  back  of  the  center 

mast, then turning the bolt in or out to adjust 

the plow ends. Retighten the jam nut once 

the  plow  is  level  with  the  ground.  Grease 

the fitting to prevent future corrosion.

23.  Fasten the power unit cover assembly onto 

the lift frame bracket with two 1/4 inch x 3/4 

inch  carriage  bolts,  flat  washers  and  lock 

nuts from the hardware bag in the parts box. 

Tighten the lock nuts so that the assembly 

is secure, yet the cover hinges freely.

DWG NO. 5843

 

Snip the plastic tie strap inside the cover as-

sembly to release the two cover latch han-

dles. When the cover is closed, rods from 

the latch handles should extend behind the 

light brackets to hold the cover in place.

24.  Assemble side markers on the ends of the 

moldboard with 5/16 inch bolts, flat washers 

and lock nuts.

DWG NO. 5854

Summary of Contents for 1852
































Reviews:

No comments