7
en
7.1.5 Fitting the chuck (TE-C und TE-T)
-NOTE-
Remove the depth gauge from the side handle in order
to avoid injury.
1. Unplug the supply cord from the mains socket.
2. Grip the sleeve around the base of the chuck and pull
it forward. Hold it in this position.
3. Push the chuck onto the guide tube on the tool and
release the sleeve.
4. Turn the chuck until it is heard to engage.
7.2 Operating the tool
-CAUTION-
G
Drilling may cause splintering of the
material.
G
Splinters may cause injury to parts
of the body and eyes.
G
Wear eye protection, protective gloves
and breathing protection if no dust
removal system is used.
-CAUTION-
G
The tool and the drilling operation
emit noise.
G
Excessive noise may damage the
hearing.
G
Wear ear protection.
7.2.1 Activating the tool (theft protection system)
(TE 16-M) (accessory available as option)
(Optional – not available with all versions.)
Further detailed information about activation and use of
this optional feature can be found in the separate oper-
ating instructions for the theft protection system.
1. Plug the supply cord into the power outlet. The yel-
low theft protection indicator lamp blinks. The power
tool is now ready to receive the signal from the acti-
vation key.
2. Hold the activation key close to the lock symbol. The
power tool is activated as soon as the theft protection
indicator lamp no longer lights.
-NOTE-
In the event of interruption of the electric supply to the
power tool, e.g. brief disconnection to move to a differ-
ent workplace, the power tool remains operational for
approx. 20 minutes. After a longer interruption, the power
tool must be reactivated by way of the activation key.
7.2.2 Drilling without hammering,
position (2
) (TE 16-M)
1. Engage the function selector switch in the (2
)
position. Do not operate the function selector switch
while the motor is running.
2. Adjust the side handle to the desired position and
check that it is fitted and secured correctly.
3. Plug the supply cord into the mains socket.
4. Position the tip of the drill bit at the point where the
hole is to be drilled.
5. Press the control switch slowly. Begin drilling at low
speed, increasing speed only after the drill bit has
become centered in the hole.
6. Press the control switch fully to continue drilling at
full power.
7. Do not apply excessive pressure to the tool. This will
not increase its hammering power. Lower contact
pressure increases the life of the insert tool.
7.2.3 Drilling without hammering, position
(
/ 1
) (TE 16/TE 16-C /TE 16-M)
1. Engage the function selector switch in the (
/
1
) position. Do not operate the func-
tion selector switch while the motor is running.
2. Adjust the side handle to the desired position and
check that it is fitted and secured correctly.
3. Plug the supply cord into the mains socket.
4. Position the tip of the drill bit at the point where the
hole is to be drilled.
5. Press the control switch slowly. Begin drilling at low
speed, increasing speed only after the drill bit has
become centered in the hole.
6. Press the control switch fully to continue drilling at
full power.
7. Do not apply excessive pressure to the tool. This will
not increase its hammering power. Lower contact
pressure increases the life of the insert tool.
7.2.4 Hammer drilling (
)
(TE 16/TE 16-C/TE 16-M)
1. Engage the function selector switch in the
(
) position. Do not operate the function
selector switch while the motor is running.
2. Adjust the side handle to the desired position and
check that it is fitted and secured correctly.
3. Plug the supply cord into the mains socket.
4. Position the tip of the drill bit at the point where the
hole is to be drilled.
5. Press the control switch slowly. Begin drilling at low
speed, increasing speed only after the drill bit has
become centered in the hole.
6. Press the control switch fully to continue drilling at
full power.
7. Do not apply excessive pressure to the tool. This will
not increase its hammering power. Lower contact
pressure increases the life of the insert tool.
8. When drilling through-holes, avoid spalling by reduc-
ing drilling speed shortly before breaking through.
-NOTE-
When working at low temperatures:
The hammering mechanism begins to operate only when
the tool has reached a minimum operating temperature.
Press the tip of the drill bit briefly against the work surface
while the tool is running. Repeat this procedure if necessary.
Printed: 07.07.2013 | Doc-Nr: PUB / 5070797 / 000 / 00
