![background image](http://html1.mh-extra.com/html/hilti/gx-120-me/gx-120-me_operating-instructions-manual_2135918019.webp)
Symbols
Read the
operating
instructions
before use.
Location of identification data on the tool
The type designation and serial number can be found on
the type identification plate on the tool. Make a note of
this data in your operating instructions and always refer
to it when making an enquiry to your Hilti representative
or service department.
Type:
Generation: 01
Serial no.:
2 Description
2.1 Use of the product as directed
The tool is designed for driving specially manufactured
nails (fasteners) into concrete, steel and other materials
suitable for the direct fastening technique (please refer to
the Fastening Technology Manual).
The tool is designed for professional use in fastening
applications in the drywall installation trade and other
building trades where fasteners are driven into concrete,
steel, sand-lime block, concrete block and rendered
masonry.
The tool, gas can and fasteners form a single technical
unit. This means that the tool can achieve optimum
fastening performance only when used in conjunction
with the Hilti fasteners and gas cans specially designed
and manufactured for it. The fastening and application
recommendations given by Hilti apply only when these
conditions are observed.
The tool is for hand-held use only.
The tool may be operated, serviced and repaired only by
trained personnel. This personnel must be informed of
any special hazards that may be encountered.
Modification of the tool is not permissible.
Observe the information printed in the operating instruc-
tions concerning operation, care and maintenance.
The tool and its ancillary equipment may present hazards
when used incorrectly by untrained personnel or when
used not as directed.
3 Accessories, consumables
Designation
Description
Gas can
GC 21/ GC 22
Nosepiece
X‑120 ME TN
Additional nosepieces
X‑120 WH (washers)
Magazine
X‑120 GM 40/ X‑120 GM 20
Support leg
X‑120 SL
Set of pin punches
X‑120 NP set
Tool clip
X‑120 TS
Nails
Length
In magazine strips of
For use on (please
contact Hilti for de-
tailed information)
X‑EGN 14MX
14 mm (¹/₂")
10
Steel
X‑EGN 18MX
18 mm (¹¹/₁₆")
10
Hard concrete /
precast concrete /
steel
X‑EGN 20MX
20 mm (³/₄")
10
Hard concrete /
precast concrete /
steel
en
15
Printed: 28.11.2013 | Doc-Nr: PUB / 5069877 / 000 / 02
Summary of Contents for GX 120-ME
