background image

Technical Data 

183/299 

PC Cards cifX Compact PCI, Mini PCI, Mini PCIe, PCI-104 | Installation, Operation and Hardware Description  
DOC120205UM53EN | Revision 53 | English | 2019-03 | Released | Public  

© Hilscher, 2008-2019 

CIFX 90-CO\F 

Parameter 

Value 

EN 61000-6-2:2005 + B1:2011 (for industrial 
environments) 

UL Certification 

The device CIFX 90-CO\F is 
certified according to UL 508 

UL-File-Nr. E221530 

Configuration Software  
Master and Slave 

SYCON.net 

Configuration 

Configuration Software Slave 

netX Configuration Tool 

Table 137: Technical Data CIFX 90-CO\F 

 

10.1.8 CIFX 

90-DN\F 

CIFX 90-DN\F 

Parameter 

Value 

Name, Part No. 

CIFX 90-DN\F 

1290.510 

Description 

PC Card cifX Mini PCI DeviceNet Master or Slave 
composed of: 
- Basic card CIFX 90 with cable connector Fieldbus X3 

and

 

- DeviceNet detached network interface (AIFX-DN). 

Note:

 The device height and the power input of the PC Card cifX 

Mini PCI CIFX 90-DN\F do not comply with the standard 
specifications.

 

Part 

Function 

Communication interface with Mini PCI-Socket and 
DeviceNet interface 

Communication 
Controller 

Type netX 

100 

processor 

RAM 

8 MB SDRAM 

FLASH  

4 MB serial Flash EPROM 

Integrated Memory 

Size of the Dual-Port Memory 

64 KByte 

Bus Type 

Mini PCI, according to [bus spec 5], refer to section 

Overview

, page 165 and 

Pin Assignment for Mini PCI Bus, 

X1

, page 166. 

Transmission Rate 

33 MHz 

Data Access 

DPM or DMA (Direct Memory Access) 

System Interface 

Width for the data access to the 
Dual-Port Memory (DPM) 

32-Bit  

DeviceNet 
Communication 

Supported communication 
standard/ protocol (determined by 
the loaded firmware) 

DeviceNet Master,  
DeviceNet Slave 

Transmission rate 

125 kBit/s, 250 kBit/s, 500 kBit/s 

Interface Type 

ISO-11898 according to DeviceNet specification,  
refer to section 

DeviceNet Interface

, page 155 

DeviceNet detached Network 
Interface 

AIFX-DN, refer to section 

AIFX-DN, 

page 231. 

Important! 

Operating the PC card CIFX 90-DN\F requires proper 

connection of the DeviceNet detached network interface (AIFX-
DN) to the basic card! 

DeviceNet Interface 

Connector AIFX-DN 

Connector Fieldbus X3  
(JST 10FMN-SMT-A-TF(LF)(SN), Pitch 1,0 mm) 

SYS 

System Status LED 

Display LED 

Display 

For LED at AIFX-DN, refer to section 

AIFX-DN, 

p. 231. 

Supply Voltage 

+3.3 V dc ±5 %, refer to section 

Power Supply and Host 

Interface

, page 61. 

Current consumption at 3.3 V 

650 mA (maximum) 

Power supply 

Connector 

Via Mini PCI Bus 

Environmental 

Operating temperature range* 

-20 °C ... +70 °C 

(

acc. to UL: 0 °C ... +70 °C

)

 

Summary of Contents for CIFX Series












































































































































































































































































































Reviews: