hilscher 1912.112 User Manual Download

Page: 101 / 154

Communication

101/154

10.1.4

Input process data status

Bit

Description

0 … 2

Reserved

IO-Link event available

This bit has the same value as attribute 20 of the instance of the Event Log Object
65 (0x41).

0: No IO-Link event is available.

1: IO-Link event is available in the instance for the port of the Event Log Object.

Reserved

Device communication (DevCom)

0: The connected device is not in PreOperate or Operate state.

1: The connected device is in PreOperate or Operate state.

Device error (DevErr)

0: No error, no warning.

1: Error or a warning occurred assigned to either device or port.

Port qualifier (PQ)

0: Input process data is not valid.

1: Input process data is valid.

Table 59: Input data status

Summary of Contents for 1912.112



























































































































































Search results

Summary of Contents for 1912.112

Reviews:

Related manuals for 1912.112

Brands by name

Popular brands

hilscher 1912.112, User Manual

Search results

Summary of Contents for 1912.112

Reviews:

Related manuals for 1912.112

Brands by name

Popular brands