RB31160 Issue 2 28/06/16
© Hills Ltd, A&TV 2016
www.hillsantenna.com.au
2)
Install the clamp
bracket and U-bolt to
the pole and finger
tighten the nuts. The
bracket will grip the
mast. Fit the antenna
to the bracket by as
shown in Figure 3.
3)
Trim the cable boot as shown in Figure 4. A
neat trim will minimise water ingress. Slide
the boot onto the cable and fit an F-type
connector (not included), as per the
manufacturer’s instructions.
4)
Screw the connector onto the balun, being careful not to over-tighten
(recommended torque is 20 in-lbs). Slide the cable boot over the
connector. Refer Figure 2.
5)
Aim the antenna towards the transmitter and tighten the nuts on the clamp
bracket with a 10mm spanner. Tie the cable to the mounting pole, being
careful to avoid sharp bends – refer to the manufacturer’s data for the
minimum bending radius of the cable.
Figure 4
Figure 3
Figure 5
WARRANTY TERMS – Australian Consumer Law
1.
Hills Antenna & TV Systems provides consumers with the following warranty in relation to this
Equipment, in addition to complying with the requirements of any relevant legislation,
including the
Competition and Consumer Act 2010
(Cth) in Australia and the
Consumer
Guarantees Act 1993
in New Zealand (the
Acts
), except where a New Zealand consumer
acquires the relevant Equipment for the purposes of a business.
2.
In this warranty, we have used the following definitions:
(a)
Hills Antenna & TV Systems
,
our
or
we
means Hills Antenna & TV Systems, a division of
Hills Holdings Limited ABN 35 007 573 417 of 159 Port Road Hindmarsh South Australia
5007.
(b)
Equipment
means the goods packaged with this warranty document, or to which this
warranty document is affixed.
(c)
Material
means a material or component used by Hills Antenna & TV Systems in the
manufacture of the Equipment.
(d)
Warranty Period
means 5 years from the date of purchase of the Equipment. If the
Equipment or part (as the case may be) is repaired or replaced, there will be no extension
to the original warranty period.
(e)
Workmanship
means the handling, assembly and manufacturing processes performed by
or on behalf of Hills Antenna & TV Systems in order to manufacture the Equipment.
3.
Hills Antenna & TV Systems warrants that for the duration of the Warranty Period, the
Equipment will be free of faults arising from defects in Workmanship or Materials, on the
terms and conditions set out in this warranty.
4.
Hills Antenna & TV Systems undertakes that if during the Warranty Period, the Equipment, or
any part of the Equipment, has failed to operate correctly due to faulty Workmanship or
defective Material, it will repair or replace the Equipment or part (as the case may be) free of
charge on the following terms:
(a)
The consumer must retain proof of purchase of the Equipment. Hills Antenna & TV Systems
may reject a warranty claim on Equipment where the consumer is unable to substantiate
proof of purchase to the reasonable satisfaction of Hills Antenna & TV Systems.
(b)
The consumer must contact the relevant Hills Antenna & TV Systems Branch Office (details
listed below) or telephone 1800 720 000 upon becoming aware of a defect to any
Equipment.
(c)
Following consultation with Hills Antenna & TV Systems, we will determine whether there
is a defect, and if so we agree (at our option) to repair, replace or supply equivalent goods,
or pay the cost of any of those remedies to the consumer.
(d)
The consumer will be responsible for the collection and freight costs of returning the
Equipment to Hills Antenna & TV Systems or to any designated Hills Antenna & TV Systems
Branch Office for repair or replacement (as determined by us).
(e)
Hills Antenna & TV Systems will be responsible for the freight costs to deliver any new or
repaired Equipment to the consumer.
(f)
Please note that a service charge will apply if no fault is identified or if any fault does not
fall within the conditions of this warranty. For details of the applicable service charge,
please contact Hills Antenna & TV Systems prior to making a claim under this warranty.
