PARTS LIST
SAFETY INSTRUCTIONS
WARNING
-2-
-3-
Follow basic safety principles to reduce risk of personal injury, electric shock and fire.
Please read the following instructions prior to operating this product and keep for future use.
● Do not let children handle the
jumpstart, all onlookers should be
away from your work area. Work in
an area that is not cluttered.
● Jumpstart may be used outdoors.
Do not leave it exposed to the
elements. Do not use jumpstart in
damp or wet areas.
● Protect the jumpstart from direct
sun light. Do not use jumpstart near
flammable gases or liquids check
cables before operation. Battery
may explode due to over-heating.
● Do not carry the jumpstart by the
cable or pull the cable to remove
the plug from the mains socket.
Protect the cable from sharp
objects, heat and oil. Have it
replaced if damaged.
● Always ensure the jumpstart is not
damaged. Do not operate if in the
case of any of the cables is
damaged. Consult a qualified
person for repair.
● Do not attempt to repair or open the
jumpstart (which contains no user
serviceable
parts).
● Do not allow the battery, at any time,
to become completely discharged.
The product should be kept fully
charged when not in use. If it will be
kept in storage, then it must be
recharged every 3 months.
● The internal battery is a sealed
lead acid battery. It is classified as
non-spillable and has unique
sealing techniques to guarantee
that no electrolyte leakage will
occur. If it is necessary to replace
the battery, then it should be done by a
qualified technician only and must be
of the same specification as the
original.
● Jumpstart is designed for use with 12V
systems only. Do not use jumpstart for
any purpose other than that is
designed. For best performance do not
use more than one output at a time.
● When using the 12V DC output socket,
ensure that the plug of the item you are
to power has the positive lead to the
centre pin of the plug.
● Jumpstart is not designed to be used
as a replacement of a vehicle battery.
● Never allow the NEGATIVE and
POSITIVE leads on this unit to touch
or to touch the same metal object.
● Ensure the posts and clamps of the
vehicle battery are perfectly clean
before
use.
● When connecting the jumpstart leads
to a battery, always connect the RED
(positive, +) clamp to the unearthed
battery terminal first, then connect the
BLACK (negative, -) clamp to the
chassis or suitable engine bolt, well
away from the battery and fuel line.
● To prevent battery overheating and
consequent damage, do not exceed
our recommendations for lump starting.
● When jumpstarting ensure the area is
well
ventilated.
● Do not attempt to boost charge the
jumpstart's sealed battery.
Components
1. Indicating LED
a. Full charge indicator (Green)
b. Charging indicator (Red)
c. Top-up charge indicator(Yellow)
d. Switch-on indicator(Green)
2. DC 3V, 6V, 9V Output Jack
3. 12V Output Socket
4. Replaceable Fuse
5. Switch for Multiple Voltage Output
and AC or DC Charging
6. 12 Volt Cigarette Lighter Lead
a. Adaptor
b. Adaptor lead
7. Booster Cable and Crocodile Clamp
a
. Negative(-)(Black)
b. Po)(Red)
8. Charging Socket
9. Fluorescent Light On/Off Switch
10. Fluorescent Light
11. AC Charger
Use
To indicate the status of the internal battery
being recharged or the on/off status of the
multiple voltage output
To allow insertion of the plug of any DC3V, 6V,
9V appliance with corresponding rated current.
This has over current protection.
To allow insertion of the cigarette lighter plug of
any DC 12V appliance.
This has over load protection.
This is an overload protection for the multiple
voltage output (3V, 6V & 9V).
To switch on DC 3V, 6V, 9V and 12V output
or to charge the internal battery
To charge the internal battery from a 12V DC
supply or allows output connection from the
cigarette socket, item 3
To connect to negative'-' battery terminal
To connect to positive '+' battery terminal
For 12V cigarette lighter lead or AC charger to
charge the internal battery
To switch the fluorescent light ON or OFF
To provide light for road side repairs and
emergency situation
To charge the internal battery
via AC 230V mains source
1a
1b
1c
1d
2
3
4
5
7b
6
7a
8
9
10
11
Dia 1
