7
5
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Set Up with App
You can view the device status including temperature, signal intensity, ba�ery level, lid, etc.,on the device page.
Tap the
bu�on to enter the se�ngs page.
6
Test
1 S
……
……
Test the smoke detector weekly by pressing firmly on the test
button with your finger for around 1 seconds until the horn
sounds, the sound pattern is 3 tone, pause, and then 3 tone with
red LED flashing continuously and rapidly. If the smoke detector
“beeps” with yellow LED flashing in 48 seconds, it indicates the
smoke detector is not working properly, it requires to be repaired
or serviced.
WARNING
: Never use an open flame of any kind to test your
smoke detector. You may set fire to damage the alarm, as well as
your home. The built-in test button accurately tests all functions
as required by Underwriters’ Laboratories. They are the only
correct ways to test the unit.
WARNING
: When you are not testing the unit and the alarm horn
sounds, this means the smoke detector has sensed high
temperature. Be sure that the alarm horn is a warning of a
possible serious situation, which requires your immediate
attention.
The alarm could be caused by a nuisance situation. Cooking
smoke or a dusty furnace, sometimes called “friendly fires” can
cause the alarm to sound. If this happens, open a window or fan
the air to remove the smoke or dust. The alarm will turn off as
soon as the air is completely clear.
NOTE
: Do not disconnect the power or remove the battery from
the smoke detector. This will remove your protection from fires.
MALFUNCTION (ERROR) SIGNAL
If you hear “beep” with yellow LED flashing once 48 seconds, it indicates that the detector doesn’t work properly, please have it repaired or serviced.
“Beep” 3 times with yellow LED flashing 1 times means that smoke trouble.
“Beep” 1 times with yellow LED flashing 1 times means that detector battery low voltage.
CLEAN ME AND LOW SENSITIVITY SIGNAL
In the case of Clean me and Low sensitive signals, please clean smoke chamber, if signal still, please have it repaired or serviced.
“Beep” 2 times with yellow LED flashing 2 times means that “Clean me”.
“Beep” 2 times with yellow LED flashing 1 times means that “Low sensitivity”.
LOW BATTERY WARNING SIGNAL
If the smoke detector horn begins to beep once every 48 seconds with yellow LED flashing, this signal means that the smoke detector’s battery is weak.
8
Opera�on Cau�on and Device Maintenance
- All the electronic opera�on should be strictly compliance with the electrical safety regula�ons, fire preven�on regula�ons and other related
regula�ons in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagne�sm radia�on. Avoid the equipment
installa�on on vibra�ons surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service
center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagne�sm radia�on. Avoid the equipment
installa�on on vibra�ons surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specifica�on of the device for the detailed opera�on temperature), cold, dusty or
damp loca�ons, and do not expose it to high electromagne�c radia�on.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ven�la�on or heat source such as heater or radiator is forbidden (ignorance can cause fire
danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunc�on however), and
affec�ng the endurance of sensor at the same �me.
- Improper use or replacement of the ba�ery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of
used ba�eries according to the instruc�ons provided by the ba�ery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situa�on.
- Open the cover and vacuum the dust off the Smoke detector’s sensing chamber at least once a month.
Remove battery before cleaning. To clean smoke detector, use soft brush attachment to your vacuum. Carefully remove any dust on smoke
detector components, especially on the openings of the sensing chamber. Replace battery after cleaning. Test the smoke detector to make sure
battery is working correctly. Never use water, cleaners as they may damage the unit.