HIKVISION DS-PDMCK-EG2-WE, User Manual, Page: 6 / 6

11 Specification
10 Operation Caution and Device Maintenance
- All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related
regulations in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service
center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specification of the device for the detailed operation temperature), cold, dusty or
damp locations, and do not expose it to high electromagnetic radiation.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire
danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and
affecting the endurance of sensor at the same time.
- Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of
used batteries according to the instructions provided by the battery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situation.
Detec ti on ga p According to the m agnet detec ti on p er f or m ance table
O ne reed switch Y es
Ex ternal in p uts 2
S hock detec ti on Y es
Tilt detec ti on Up to 2 5°
Ta mp er p rotec ti on F ront & B ack
L E D indicator G reen ( MC ) , O range (ti lt ) , R ed ( shock ) , B lue ( alar m)
E nca p sulated p las ti c Y es
I n p ut o pti ons N or m al and F ast S ensi ti vity with P ulse Count
P rogra mm able p ulse count Y es
F ast in p ut sensi ti vity 1 m s
N or m al in p ut sensi ti vity 3 00 m s
Op era ti ng te mp erature
- 10 ° C to 55 ° C ( 1 4 °F to 1 3 1 °F)
- 10 ° C to 4 0 ° C ( 1 4 °F to 10 4 °F) Cer tifi ed
S torage te mp erature - 20 ° C to 6 0 ° C (-4 °F to 1 4 0 °F)
Op era ti ng hu m idity 10% to 9 0%
Di m ension ( H × W × D )
S ensor : 22. 5mm × 10 3mm × 2 3 .2 mm
Magnet : 1 3mm × 34 . 4mm × 11. 4mm
W eight 6 0 g
W ireless technology Tri -X W ireless Technology
P rogra mm ing m ethod Advanced W ireless Link
L E D indicator O n /Off
S hock sensi ti vity ad j ust m ent High /N or m al / Low
Tilt 5° to 2 5°
Ex ternal I n p ut 1 N C /NO , R oller S hu tt er (RS) , Ta mp er
Ex ternal I n p ut 2 N C /NO , R oller S hu tt er (RS) , Ta mp er
RS P ulse Count 2 to 3 0 P ulses
RS P ulse Count Ti m eout 10 to 6 0s
E nviron m ent te mp erature indicator Y es
2 - way wireless co mm unica ti on Y es
Trans m ission f re q uency 868 MHz
F re q uency ho pp ing Mul ti channel trans m iss ti on
Trans m ission encry pti on A ES- 12 8 encry pti on
S ignal strength indicators Y es
RF range 1. 6 k m ( o p en area )
E nrolling m ethods P ower u p , R e m ote I D, QR code
B a tt ery C R 12 3 A x 1 ( included )
S tandard ba tt ery li f e 3 years
6
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China