background image

Mobile Digital Video Recorder User Manual 

autorisée aux deux conditions suivantes : 

(1) l'appareil ne doit pas produire de brouillage, et 

(2)  l'utilisateur  de  l'appareil  doit  accepter  tout  brouillage  radioélectrique  subi,  même  si  le  brouillage  est  susceptible  d'en 

compromettre le fonctionnement. 

Under Industry Canada regulations, this radio transmitter may  only operate using an antenna of a type and maximum (or lesser) 

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and 

its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful 

communication. 

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut 

fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le 

but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son 

gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une 

communication satisfaisante. 

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. 

Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.

   

Summary of Contents for DS-MP3504-SD Series


















Reviews: