Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Screw the bolts through the mount by aligning
with the 2 bolt holes. Fit the toggles onto the bolts.
3.Push the two toggle bolts through the two screw
holes on the ceiling. Rotate the bolt till the toggle
holds the ceiling tightly.
2.2 In-ceiling Mounting
Figure 2-5 Install the Mount
Figure 2-6 Fix the Camera to the Mount
Figure 2-8 Fix the Camera to the Gang Box
6. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
4.Route and connect the corresponding cables.
5.Fix the camera to the in-ceiling mount with the
supplied screws.
3.Attach the back box of type 1 camera /base plate
of type2 camera to the ceiling and secure them
with supplied self-tapping screws.
4.Route the cables through the cable hole.
5.Align the camera with the back box/base plate,
and tighten the set screws to secure the camera
with the back box/base plate.
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adjust the camera according to the figure below
to get an optimum angle.
8. Fit the black liner on the camera and tighten the
screws on the bubble of type 1 camera or rotate the
bubble of type 2 camera to complete.
Figure 2-4 3-axis Adjustment
You need to purchase an in-ceiling mount separately
if you adopt in-celling mounting.
2.3 In-ceiling Mounting
in-ceiling mounting with gang box is supported by
the both types of camera.
1.Repeat steps 2-3 of the In-ceiling Mounting
section to secure the in-ceiling mount (supplied)
to the gang box.
Figure 2-7 Install the Mount
2.Route and connect the corresponding cables.
3.Align the camera with the gang box, and tighten
the screws to secure the camera with the gang box..
5. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
Type I:
Type I :
I
0 ~75
°
°
0 ~355
°
°
0 ~355
°
°
P Direction
R Direction
T Direction
Type I:
0
°
~355
°
0 ~75
°
°
0 ~340
°
°
T Direction
R Direction
P Direction
Type I :
I
Type I:
Type I :
I
Type I :
I
Type I :
I
3.2.2 WB
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the
,
BRIGHTNESS EXPOSURE
MODE
AGC
, and
.
:
Brightness
Brightness refers to the brightness of the image.
Exposure Mode:
Move the cursor to
, you can select
Exposure Mode
the exposure mode between
and
.
Globe
BLC
When BLC is selected as the exposure mode, the
level of BLC mode can be adjusted, as shown in the
Figure 3-2.
3.2.4 VIDEO SET TING
Contrast
:
Contrast enhances the difference in color and light
between parts of an image.
You can set the value from 1 to
.
10
Sharpness
:
Sharpness determines the amount of
detail that an imaging system can reproduce.
You can set the value from 1 to 10.
Saturation:
You can set the saturation level of the image. The
value is from 0 to 10.
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from
0 to 7.
:
Mirror
You can set the Mirror status as H, V, HV, or OFF.
3 Menu Operation
Figure 3-1 Main Menu
VIDEO
SETTING
DAY/NIGHT
WB
RESET
BRIGHTNESS
MODE
INFRARED
SMART IR
CONTRAST
SHARPNESS
SATURATION
EXIT
AE
DNR
MIRROR
EXPOSURE MODE
AGC
SAVE/EXIT
With a coaxial camera controller (purchase
separately) or calling the preset No.95 you can
select the menu and adjust the camera parameters.
3.1 FORMAT
You can set the format as PAL/NTSC.
3.2 SET UP
Move the cursor to
, and press menu button
SET UP
to enter the SET UP sub menu.
EXPOSURE
1.BRIGHTNESS
2.EXPOSURE MODE
LEVEL
3.AGC
4.RETURN
5
BLC
5
MIDDLE
Move the cursor to WB, and you can set White
Balance mode as
and
in this menu
AWB
MWB
.
AWB:
white balance is being adjusted
automatically.
: Set the
value from 1 to 10.
MWB
R GAIN/B GAIN
As shown in Figure 3-3.
WB
MODE
MWB
R GIAN
1-|--10
B GAIN
1-|--10
RETURN
8
AGC
:
AGC optimizes the clarity of image in poor light
scene. AGC level can be set as OFF, LOW, MIDDLE
and HIGH.
Figure 3-2 EXPOSURE
Figure 3-3 WB
Figure 3-4 DAY/NIGHT
3.2.3 DAY & NIGHT
Move the cursor to DAY & NIGHT, and select
COLOR B/W
SMART
,
, or
as the DAY & NIGHT mode.
COLOR
: The image is colored in day mode all the
time.
: The image is black & white all the time, and
B/W
the IR LED turns on in the low-light conditions.
: Select to turn on/off the INFRARED_LAMP
SMART
and to set the Smart IR level from 1to 16.
As shown in Figure 3-4.
DAY/NIGHT
MODE
SMART
INFRARED
OFF
SMART IR
0-|--5
RETURN
8
3.2.7 SAVE/EXIT
3.2.5 Reset
Reset all the settings to the default.
3.2.6 EXIT
Exit and Save & exit are selectable.
Move the cursor to
, and press OK to
SAVE & Exit
save the settings and exit the menu.