manualshive.com logo in svg

HIKVISION DS-2CD series, Installation Manual, Page: 104 / 131

Share
Download
HIKVISION DS-2CD series Installation Manual Download Page 104

Installation Manual of Network Camera 

103

 

Tilt Adjust Nut

Pan Adjust Nut

 

Figure 4-38

 

Adjust Monitoring Angle 

 

 

Please  loosen  the  screws  slightly  until  you  can  adjust  the  camera  and  do  not  remove  the 
screws from the bracket. 

 

After  the  monitoring  angle  is  adjusted,  you  may  need  to  install  a  water-proof  rubber  case 
(purchased separately) to the foldable position of the bracket to protect it from water. 

8.

 

Loosen the lock screw on the sun shield and remove the sun shield. 

9.

 

Rotate to remove the front box from camera and adjust the zoom lever and focus lever to get 
a clear image. 

Zoom Lever

Remove the Sun Shield

Romove the Front Box

Focus Lever

 

Figure 4-39

 

Lens Adjustment 

10.

 

Reinstall the front box and the sun shield to finish the installation. 

Lo-Call 1890 866 900

www.cctvireland.ie

[email protected]

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for DS-2CD series




































































































































Reviews:

No comments