11
Status of indicator
2 LEDs (Red) light
The battery remaining
power is enough.
1 LED (Red) lights
The battery remaining
power is about half.
1 LED (Red) blinks
The battery remaining
power is nearly empty.
Recharge the battery as
soon as possible.
(5) Other functions
In case of operation error, LED lamps show as below.
Status of indicator
LED light
LED light blink in an interval.
• In case of too hot
condition, Blink in
1 second interval.
• In case of too cold
condition, Blink in
0.5 second interval.
After 10 seconds,
automatically turn o
ff
LED
light and Power switch.
Machine is in too cold
(below -5°C or too hot
condition.
Allow the nailer to cool
or warm-up thoroughly in
adequate condition.
2 LEDs blink in Orange,
after 10 seconds,
automatically turn o
ff
Power switch.
Contact HiKOKI for
inspection.
(6) How to use the LED light (See
Fig. 7
)
While the power switch on, the LED light will automatically
light up the tip portion of the tool.
CAUTION
○
Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
○
Wipe o
ff
any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
2. Trigger Lock Mechanism (See Fig. 8)
WARNING
Make sure the trigger is locked when not
fi
ring nails.
This Nailer has a lock mechanism to prevent the nails
from being
fi
red.
Set the switch lock lever at the position to lock the
trigger.
Slide the switch lock lever to the position when the
Nailer is to be used, and to the position when it is not
in use.
3. Testing the nailer
WARNING
○
Make sure the trigger is locked when not
fi
ring nails.
(See
Fig. 8
)
○
Never use Nailer unless push lever is operating properly.
The NT1865DMA and NT1865DM employ a preventive
mechanism for unloaded operation.
The NT1865DMA and NT1865DM enter a state where
the push lever cannot be pushed up. This takes place
when the magazine is not loaded with nails or when the
remaining number of nails becomes less than 6 or 9.
CAUTION
Use caution not to throw the push lever tip onto wood.
Before actually beginning the nailing work, test the Nailer by
using the checklist below. Conduct the tests in the following
order.
If abnormal operation occurs, stop using the Nailer and
contact a HiKOKI authorized service center immediately.
(1) REMOVE ALL NAILS AND BATTERY FROM NAILER.
□
ALL SCREWS MUST BE TIGHTENED.
□
THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY with pulling back the nail feeder (B).
(NT1850DE: Unnecessary to pulling back nail
feeder)
(2) Installing the battery.
Do not operate the push lever or trigger while installing
the battery. (See
Fig. 2
)
(3) Turn on the Power switch. (See
Fig. 1
)
Turn on the Power switch by push and hold on Power
switch more than 1 second.
Make sure the power indicator is lighting in green, and
nailing operation indicator is lighting in blue. (FULL
SEQUENTIAL ACTUATION MECHANISM)
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power o
ff
]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned o
ff
. To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
Nailing operation indicator
Lighting
(Blue):
FULL SEQUENTIAL ACTUATION MECHANISM,
Blinking
(Blue):
CONTACT ACTUATION MECHANISM
Make sure the battery indicator is not blinking.
If the battery indicator is blinking in red, the battery
doesn’t have enough power and it needs to be charged.
(4) Remove the
fi
nger from the trigger and press the push
lever against the workpiece with pulling back the nail
feeder (B).
□
THE NAILER MUST NOT OPERATE.
00Book̲NT1865DMA.indb 11
00Book̲NT1865DMA.indb 11
2021/04/02 11:47:05
2021/04/02 11:47:05
