HIKOKI G 18DBL Handling Instructions Manual Download Page 9

9

  Regarding the temperatures and charging time of the battery.

 

The temperatures and charging time will become as shown in 

Table 2-a (UC18YFSL), Table 2-b (UC18YSL3)

Table 2-a

Charger

UC18YFSL

Battery

Type of battery

Li-ion

Temperatures at which the 

battery can be recharged

0°C – 50°C

Charging voltage

V

14.4

18

Charging time, 

approx. (At 20°C)

BSL14xx series

BSL18xx series

Multi volt 

series

(4 cells)

(8 cells)

(5 cells)

(10 cells)

(10 cells)

min.

BSL1415S : 20

BSL1415  : 22

BSL1415X : 22

BSL1420  : 30 

BSL1425  : 35

BSL1430C : 45

BSL1430  : 45

BSL1440  : 60

BSL1450  : 75 

BSL1460  : 90

BSL1815S : 20

BSL1815 : 22

BSL1815X : 22

BSL1820 : 30

BSL1825 : 35

BSL1830C : 45

BSL1830 : 45

BSL1840 : 60

BSL1850 : 75 

BSL1860 : 90

BSL36A18 :  75

BSL36B18 : 120

Table 2-b

Charger

UC18YSL3

Battery

Type of battery

Li-ion

Temperatures at which the 

battery can be recharged

0°C – 50°C

Charging voltage

V

14.4

18

Charging time, 

approx. (At 20°C)

BSL14xx series

BSL18xx series

Multi volt 

series

(4 cells)

(8 cells)

(5 cells)

(10 cells)

(10 cells)

min.

BSL1415S : 15

BSL1415  : 15

BSL1415X : 15

BSL1420  : 20 

BSL1425  : 25

BSL1430C : 30

BSL1430  : 20

BSL1440  : 26

BSL1450  : 32 

BSL1460  : 38

BSL1815S : 15

BSL1815 : 15

BSL1815X : 15

BSL1820 : 20

BSL1825 : 25

BSL1830C : 30

BSL1830 : 20

BSL1840 : 26

BSL1850 : 32 

BSL1860 : 38

BSL36A18 : 32

BSL36B18 : 52

USB

Charging voltage

V

5

Charging current

A

2

NOTE

 

The recharging time may vary according to the ambient 

temperature and power source voltage.

CAUTION

  When the battery charger has been continuously used, 

the battery charger will be heated, thus constituting 

the cause of the failures. Once the charging has been 

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the 

receptacle.

5.  Hold the charger 

fi

 rmly and pull out the battery.

NOTE

 

Be sure to pull out the battery from the charger after use, 

and then keep it.

CAUTION

  If the battery is charged while it is heated because it has 

been left for a long time in a location subject to direct 

sunlight or because the battery has just been used, the 

pilot lamp of UC18YFSL charger lights for 1 second, 

does not light for 0.5 seconds (o

  for 0.5 seconds), or 

the charge indicator lamp of UC18YSL3 charger lights 

for 0.3 seconds, does not light for 0.3 seconds (o

  for 0.3 

seconds). In such a case, 

fi

 rst let the battery cool, then 

start charging.

 

When the pilot lamp or charge indicator lamp 

fl

 ickers in 

red (at 0.2-seconds intervals), check for and take out 

any foreign objects in the charger’s battery connector. If 

there are no foreign objects, it is probable that the battery 

or charger is malfunctioning. Take it to your authorized 

Service Center.

 

Since the built-in micro computer takes about 3 

seconds to con

fi

 rm that the battery being charged with 

charger is taken out, wait for a minimum of 3 seconds 

before reinserting it to continue charging. If the battery 

is reinserted within 3 seconds, the battery may not be 

properly charged.

0000Book̲G18DBL.indb   9

0000Book̲G18DBL.indb   9

2020/06/10   15:04:59

2020/06/10   15:04:59

Summary of Contents for G 18DBL





















Reviews: