9
– Check that the work piece is properly supported;
– Do not use cutting o
ff
wheel for side grinding;
– Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite
fl
ammable
substances;
– Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust,
fi
rst disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts;
– Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves, helmet
and apron should be worn;
– Pay attention to the wheel that continues to rotate after
the tool is switched o
ff
.
– Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
– Never disassemble the rechargeable battery and
charger.
– Never short-circuit the rechargeable battery.
Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
– Do not dispose of the battery in
fi
re. If the battery is burnt,
it may explode.
– Do not insert object into the air ventilation slots of the
charger. Inserting metal objects or in
fl
ammables into the
charger air ventilation slots will result in electrical shock
hazard or damaged charger.
– Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
ADDITIONAL SAFETY WARNINGS
1. Ensure that the depressed center wheel to be utilized is
the correct type and free of cracks or surface defects.
Also ensure that the depressed center wheel is properly
mounted and the wheel nut is securely tightened.
2. Con
fi
rm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on.
3. To prolong the life of the machine and ensure a
fi
rst
class
fi
nish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is su
ffi
cient
for e
ff
ective grinding. Too much pressure will result in
reduced rotational speed, inferior surface
fi
nish, and
overloading which could reduce the life of the machine.
4. The wheel continues to rotate after the tool is switched
o
ff
.
After switching o
ff
the machine, do not put it down until
the depressed center wheel has come to a complete
stop. Apart from avoiding serious accidents, this
precaution will reduce the amount of dust and swarf
sucked into the machine.
5. When the machine is not use, the power source should
be disconnected.
6. Be sure to switch OFF and pull out the battery to avoid
a serious accident before the depressed center wheel is
assembling and disassembling.
7. Be careful of brake kickback.
This cordless disc grinder features an electric brake that
functions when the switch is released. As there is some
kickback when the brake functions, be sure to hold the
main body securely.
8. Do not use the product if the tool or the battery terminals
(battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
9. Keep the tool’s terminals (battery mount) free of swarf
and dust.
○
Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○
During use, try to avoid swarf or dust on the tool from
falling on the battery.
○
When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result in
smoke emission or ignition.
PRECAUTIONS FOR BATTERY AND
CHARGER
1. Always charge the battery at an ambient temperature of
-10–40°C. A temperature of less than -10°C will result in
over charging which is dangerous. The battery cannot be
charged at a temperature greater than 40°C.
The most suitable temperature for charging is that of
20–25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery or charger.
5. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
6. Do not dispose of the battery in
fi
re.
If the battery is burnt, it may explode.
7. Using an exhausted battery will damage the charger.
8. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
9. Do not insert objects into the air ventilation slots of the
charger.
Inserting metal objects or
fl
ammable into the charger air
ventilation slots will result in an electrical shock hazard or
damage to the charger.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such a case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○
During work make sure that swarf and dust do not fall on
the battery.
000Book̲G3610DA̲AUST.indb 9
000Book̲G3610DA̲AUST.indb 9
2021/04/26 9:27:59
2021/04/26 9:27:59
