background image

 

 

8

9

MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0

MA-EN-OSMOSIS XENA10.1-RO-0220-22-FLC-21-V01.0

 

To fit the membrane (Figure-2) in the membrane housing correctly, the membrane must be 

taken out of its packaging and proceed as follows:

a.  Place the plug that comes with each of the membranes in the end of the permeate port of the 

membrane which has two slits as shown in the following diagram.

4.5.- Membrane installation

b.  Unscrew the inlet elbow nut on each of the membrane housing to be able to open the lid.

c.  Open the membrane housing turning it anti-clockwise with the help of the wrench supplied 

with the system (figure 4).

d. 

Insert the membranes in the correct direction as shown in the following figure. They must 

be fitted following the arrows on the respective membrane housing, introducing the end that 

doesn’t have the big exterior seal first.

c. 

Unscrew the filter housing checking that the cartridges are centered, so they ad-just 

properly with the filter adapter and cup.

d. 

Tighten the filter housing with using the wrench supplied with the system (figure 4).

e. 

Once the membranes have been fitted, close the membrane housing lid clock-wise with the 

help of the wrench supplied with the system (figure 4). Then screw the inlet elbow nuts back 

on the membrane housing

a.  Place the osmosis system in the chosen location.

b. 

Connect  ⅜”  tube  (figure  6)  to  the  brass  ball  valve 

connected water supply inlet (figure 9).

c. 

The other end of the ⅜” tube must be connected to 

the inlet of the pressure reducer (figure 15); to do 

so, you must remove the blue safety clip on the inlet 

and insert the tube fully. Once you have inserted the 

tube,  put  the  ⅜”  safety  clip  back  on  (the  pressure 

reducer has a label with an arrow which indicates 

the water flow.

 

The hydraulic connections should follow the contour of the surface chosen for installation so 

that the tubes do not get mixed up or tangled. Leave a sufficient length of tube to ease moving the 

system during future maintenance. Here are the steps to follow to make the hydraulic connection:

4.6.- Osmosis system installation

Summary of Contents for XENA 10.1














Reviews: