Hidrex DP450 User Manual Download Page 5

  Rev. 1.4 / 02-16-2017        

DP450 Tap Water Iontophoresis System User Manual

 

 
 

 

 

Prior to using AC wall power, check that your outlet meets the system’s 
requirements of 110-230 V~ and 50-60 Hz. 

 

Unplug the AC power adapter if a thunderstorm approaches or if you do 
not intend to use the system for an extended period of time.  

 

This device should only  be  used indoors. Do not expose the device to 
rain or excessive moisture.  

 

Do  not  use  kerosene,  thinner,  alcohol,  wax  remover  or  any  other 
solvents. 

 

Prior  to  cleaning  the  device,  turn  off  the  device  and  unplug  all 
connectors.  For  cleaning,  use  a  soft  cloth  moistened  with  a  mild 
cleaning agent. 

 

Prevent  kinking  of  the  cable  and  do  not  expose  the  cable  to  heat  or 
chemicals. If the cable is damaged, unplug it from the device and have it 
checked by an authorized HIDREX repair center. 

 

Never  open  the  device;  there  are  no  control  elements  inside.  The 
system may only be serviced by an authorized HIDREX repair center. 

 

Wash the supplied towels on a regular basis together with your regular 
laundry (make sure to comply with the laundry instructions on the tag). 

Intended Use / Mechanism of Action 

Intended Use: 

This  tap  water  iontophoresis  device  is  intended  to  treat 
hyperhidrosis

1

  (excessive

 

sweating)  affecting  hands,  feet  and 

underarms.

 

 

Any  other  use  or  usage  beyond  this  scope  is  considered  un-
intended use and may have dangerous consequences. 

Mechanism of Action: 

During the HIDREX treatment, a current flows through the body regions that 
are being treated. The water in the trays or pads mediates this current flow. 
The skin areas in contact with the water will thereby secrete less sweat. 

Although  treatment  success  has  been  validated  in  numerous medical  stud-
ies,  there  is  still  no  completely  satisfactory  scientific  explanation  for  the 
mechanism of action. Medical researchers believe that the electrical current 
irritates  the  synapses  between  sweat-inducing  nerves  and  sweat  glands  to 
such  an  extent  that  sweat  glands  can  no  longer  be  stimulated.  In  other 
words: the treatment does not affect the sweat glands directly, it only affects 
the nervous input to these glands. 

This effect explains why the original condition returns relatively quick-
ly when the treatment is discontinued. 

                                           

1

 Additional indications include: Dyshidrotic dermatitis, palmoplantar pustolosis and acrocynosis. 

Summary of Contents for DP450





























Reviews: