manualshive.com logo in svg

Hico Medical Systems HICO-VARIOTHERM 550, Instructions For Use Manual

Share
Download
Hico Medical Systems HICO-VARIOTHERM 550 Instructions For Use Manual Download Page 9

 

Safety 

HICO-VARIOTHERM 550

 

 

9

 

2  Safety 

This chapter contains important safety notes for work with this 
unit. 
This unit complies with the specified safety regulations. However, 
improper use can lead to personal injury or material damage. 

2.1 Intended use 

This unit is solely intended for the cooling or heating of water 
pads

1

 used to cool or warm a patient. Any other use exceeding 

the use described above is considered as unintended use.  

The pads available as an accessory may only be used with HICO 
units for use in hypo/hyperthermia treatment. 

•

 

 

Danger due to improper utilisation! 

Dangers may arise from the unit if it is put to unintended use 
and/or if it is used for any other purpose. 
►  Only use the unit for the purpose it is intended for. 
►  Observe the procedures described in these operating 

instructions. 

►  Use only with original accessories 
 

Claims of any type because of damages resulting from 
unintended use are excluded. 

The operating company is the sole bearer of the risk. 

 

                                            

1

 In these operating instructions the term "water pad" describes all Hirtz accessories, such as water mats, water blankets, 

water collars, etc. (see also chapter 11.2 

Accessories

) 

Summary of Contents for HICO-VARIOTHERM 550










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands