background image

 

Qcool Intelligent Handled GPS

 

3

 

may  cause  harmful  interference  to  radio  communications.   However,  there  is  no 
guarantee  that  interference  will  not  occur  in  a  particular  installation.   If  this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:

 

- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 

-Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

FCC ID: O39ZHDQCOOL 

This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.

 

 

International Limited Warranty, Software Licence   

Agreement 

You must not install or use the software unless you have read and accepted the terms and 
conditions of the HI-TARGET software Licence Agreement. Installation or use of the software or 
any part thereof, is deemed to be an acceptance of all the terms and conditions of such Licence 
Agreement. 

Responsibility absolution 

Before you use the product, you should read the introduction carefully. Guangzhou HI-TARGET 
surveying  and  mapping  instruments  Co.,  LTD.  We  will  not  take  the  responsibility  if  you  not 
operate within the product instruction

 

Guangzhou HI-TARGET surveying and mapping instruments Co., LTD. Is committed to 
continuously improve product function and performance, improve the service quality, and keep 
the right to change the content of the instruction without notice in advance. 
We have to print described in the content and the consistency of the hardware and software to 
do an inspection, but don't rule out the possibility of bias, the picture in the instruction for use 
for reference only, if you have a product with discrepancies, please use the product kind prevail. 

Summary of Contents for Qcool Series















Reviews: