HHP Adaptus Image Kiosk TT8870 Programming Manual Download Page 71

Page: 71 / 149

Image Kiosk™ TT8870 Programming Guide

5 - 29

Linear Symbologies

MSI

MSI

MSI Check Character

Different types of check characters are used with MSI bar codes. You can
program the imager to read MSI bar codes with Type 10 check characters.

Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to

Validate and Transmit

, the imager will only

read MSI bar codes printed with the specified type check character, and will
transmit this character at the end of the scanned data.
When Check Character is set to

Validate, but Don’t Transmit

, the unit will only

read MSI bar codes printed with the specified type check character, but will not
transmit the check character with the scanned data.

* Off

Validate Type 10 and Transmit

* Validate Type 10, but Don’t

Transmit

Summary of Contents for Adaptus Image Kiosk TT8870






















































































































































Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands

HHP Adaptus Image Kiosk TT8870, Programming Manual

Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands