HF PackerAmp V4 Construction Manual Download Page 33

Page: 33 / 76

HF PACKER

AMP

V4R6

Page 33

PINET 100-PI Option Module



section is for those who purchased the PINET 100-PI

Option Module. (skip this section otherwise)

100-PI Assembly

•

Install Diodes D1 and D2

•

Install Relays K1 and K2

•

Install Connectors J1, J2, J3 and J4 according to

silkscreen pattern.

•

Install Resistors R1, R2, R3, R4, R5 and R6 (refer

BOM)

•

Clean circuit board and set aside after inspection.

100-PI Cable Fabrication

•

Fabricate two 3-inch cables. Use the supplied RG174

cable, black 1 ¼ inch hook up wire and shrink tubing.

•

Strip ½ inch insulation from each end. Twist the braid

and trim to ¼ inch. Tin the braid and attach a black

hookup wire to the braid. Cover with heat shrink tubing.
The wires are positioned as shown.

•

Attach a 2-pin connector on one end of each cable.

Note in the picture that the openings for the terminal
tabs are up in the picture. Attach the coax center wire
to the pin indicated in the picture.

•

Fabricate a

five inch 2-wire cable from the red/black wires supplied.
Attach a crimp terminal to one end of each wire. Strip
3/8 inch insulation from the other ends and tin the wire
lightly.

•

Insert the crimp terminals in the 2-pin housing as

shown below. Note in the picture that the openings for
the terminal tabs are up in the picture.

•

Install a 430 ohm resistor at R7 and R8. Install a 12

ohm resistor at R3. This is the new 2dB pi-resistive
network.

Summary of Contents for PackerAmp V4













































































Search results

Summary of Contents for PackerAmp V4

Reviews:

Related manuals for PackerAmp V4

Brands by name

Popular brands

HF PackerAmp V4, Construction Manual

Search results

Summary of Contents for PackerAmp V4

Reviews:

Related manuals for PackerAmp V4

Brands by name

Popular brands