GB
English
English
13
14
www.heyner-germany.de
www.heyner-germany.de
1. GROUP I (about 9 to 18 kg Y)
1.1. Using HEYNER® CapsulaProtect 3D as a child car seat
HEYNER® CapsulaProtect 3D
1.2. Adjusting HEYNER® CapsulaProtect 3D to your child's
size
1.2.1. Preparation
fig.1a-c
HEYNER® CapsulaProtect 3D
HEYNER® CapsulaProtect 3D
HEYNER® CapsulaProtect 3D
belts, make sure that the shoulder belts (SG) run down
from just above the child's shoulders (fig.1a), not too high
above them (fig.1b) and not too low (fig.1c).
1.2.2. Height and length adjustment of the shoulder belts
1.2.2. Height and length adjustment of the shoulder belts
Height adjustment of the harness belts (G2):
• The HEYNER® CapsulaProtect 3D
HEYNER® CapsulaProtect 3D consists of a seat part (ST)
and a base part (BT), which are connected by a
safety bolt (SB).
fig.2
fig.2
• De-block the safety lock (SR) of the safety bolt at the rear
side of the base part (BT) and slide out the safety bolt (SB)
sideward’s out of the base holes (BL). Now the
seat part (ST) is de-blocked and can be flapped forward.
fig.2a
fig.2a
• Release both belt ends of the harness belts (G2) from the
belt anchorage (R) at the back of the seat part (ST),
and pull the belt ends out of the slots (G1).
• Then release the shoulder pad connector belts (SG) from the
connecting hook (VH).
• Put that are appropriate to the child's size and thread them
back into the belt anchorage (R).
• Finally put the pad connector belts (SG) under the
harness belt ends (G2) through the same belt slots (G1) and
hook them back into the connecting hook (VH).
fig.2b
fig.2b
• To release the belts (fig.2b), push the belt adjuster (I),
hidden by the cover, and pull both harness belts (G2)
simultaneously forward.
fig.2c
fig.2c
• To shorten the shoulder belts, just pull the central
harness belt (G5). Do not block the shoulder belts during
pulling.
fig.2d
fig.2d
• Now flap back the seat part (ST). Slide back the
safety bolt (SB) sideward’s into the base holes (BL). Block
the safety lock (SR) of the safety bolt at the rear side of
the base part (BT).
• Attention
Attention: The safety bolt (SB) shall has to be fixed
correctly to both seat part (ST) and base part (BT) before
the seat is placed into the car for installation.
• Attention
Attention: It is recommended to check the belt position
very regularly and to adjust it to the size of your growing
child. The belts must lie firmly against the child's body
and must not be twisted.
Important:
Important:
• The belts must not be twisted or blocked. Please refer to
the drawing. in case of any doubt or contact your seller
or dealer, importer or manufacturer.
1.3. Installing HEYNER® CapsulaProtect 3D into your car
1.3.1. Conditions for installation
fig.3
HEYNER® CapsulaProtect 3D
1.3.2. Placing on the vehicle seat
HEYNER® CapsulaProtect 3D
1.3.3. Installation and fixing
fig.4
fig.5
fig.6
fig.7
fig.8
HEYNER® CapsulaProtect 3D
fig.9
fig.10
Attention
1.3.4. Tightening of the cars belt
fig.11
HEYNER® CapsulaProtect 3D
fig.12
fig.13
fig.14
Attention
Attention
HEYNER® CapsulaProtect 3D
1.4. Travelling with the HEYNER® CapsulaProtect 3D
1.4.1 Securing the child
fig. 15
fig. 16-17
HEYNER® CapsulaProtect 3D
fig. 18
1.4.2 Sitting and Laying position of your child
fig. 19
HEYNER® CapsulaProtect 3D
2. Care instructions
fig. 20
HEYNER® CapsulaProtect 3D
fig. 21-22
fig. 23
fig. 24
Attention
Attention
HEYNER® CapsulaProtect 3D
3. Important notices
HEYNER® CapsulaProtect 3D
ECE R44/04
HEYNER® CapsulaProtect 3D
HEYNER MOBIL AUTOMOTIVE GMBH
4. Some final hints:
130.com.ua
Autogood products «130»
