1.
To illuminate the star, please only use our recommended
accessories (bulb / cable) provided with the star and a
power source suitable for 6 V /0,3 A (low-voltage current).
2.
Never plug the ends of the cabling directly into a wall socket!
3.
The screw heads of the plugs should not touch each other.
4.
Make sure that lamp and socket are well and straight fixed
into the cap. The lamp needs to be fitted in the middle of
the body.
5.
The Herrnhut star and the lighting kit is for decoration
only and is not suitable as a toy for children.
The sharp
points may cause injury. Please handle with care.
6.
The star assembly kit, model A1b might be assembled
under adult supervision and by children 7 years and older.
Attention, electric device. Do not operate without supervision!
1.
Place the bulb into the opening of the star and fasten the
cap firmly onto the neck of the star.
5.) Operating- and safety instructions
3.) Assembly instructions
2.
Now you can hang up the star with the use of the cable.
1.
Start with sticking the two halves of the body base together.
Please apply the glue slightly. Remove all remains of glue on
the splice.
3.
Now stick the remaining points onto the appropriate
elevated sections of the body base.
Single star A1e:
DIY-kit A1b:
2.
Now fix the single points onto the appropriate sections
of the body. Start with 7 square points and stick them
along the seam of the body.
4.
Please consider the colour
scheme of bicoloured stars
according to this picture.
Please apply the glue slightly!
© Herrnhuter Sterne GmbH, Subject to change 02/2018
Herrnhuter Sterne GmbH
Oderwitzer Straße 8 . 02747 Herrnhut
Tel. +49-35873 3640 . Fax +49-35873 36435
4.) Basic notes on the lighting kit
For lighting-up the star, please connect the plugs of the
lighting kit with the sockets of the power supply or battery
holder cabling. (available separately, see accessories)
Some stars are provided with LED-lamps as standard.
(concerns stars in: green, blue, green/white, blue/white, limited edition)
As power source we recommend our products:
- Power supply unit 500mA suitable for 6 V (for 1 star)
- Power supply unit 1000mA suitable for 6 V (for 1 – 3 stars)
- Battery holder for 1 star
If the LED does not light up:
Please swap the connection
pins of the lighting kit and
the power supply unit.
1.) Your product
Model:
A1e or A1b
Size:
Ø 13 cm (5,1 inches)
Colours:
yellow, white, red, yellow/red, white/red, green,
blue, green/white, blue/white, special edition
Material:
plastic (type A), for indoor use
Assembly Instructions
Herrnhut Stars A1e and A1b
Dear customer,
we would like to thank you for choosing this product
from our manufacture. We hope you enjoy your star and
have many enjoyable and uplifting moments with it.
The Herrnhut Star Company
2.) Product contents
• 2 halves of the body base
• 17 square points
• 8 triangular points
• 1 tube of glue
• 1 single star, made of plastic
• 1 lighting kit:
- 1 lamp (bulb or LED) 6.3 V, E10
- cover cap in colour of the star
- cable with plugs, lenght 3m
Model A1b (DIY-kit, self-assembly):
17 x
8 x
1 x
1 x
1 x
1 x
2 x
Model A1e (single star, assembled):
• 1 lighting kit:
- 1 lamp (bulb or LED) 6.3 V, E10
- cover cap in colour of the star
- cable with plugs, length 3m
Tip:
For better stability and handling during further
assembly, you can attach the cap of the lighting on the
neck of the body. (Do not glue the cap!)
