background image

P-51 Mustang

KIT # HRR506

WARRANTY

Herr Engineering Corp. guarantees this kit to be free from defects in both materials and workmanship at the time of

purchase.  This warranty does not cover any component damaged buy use or modification.  In no case shall Herr
Engineering Corporation’s liability exceed the original cost of the purchased kit.  Further Herr Engineering Corp.
reserves the right to change or modify this warranty without notice.

In that Herr Engineering Corporation has no control over the assembly or use, no liability shall be assumed or 

accepted for any damage resulting from the use by the user during construction of the kit or the use of the final user
assembled product.  By the act of building this kit and/or using the final user assembled product, the user accepts all 
liability.

If the buyer and/or user is not prepared to accept all of the liability associated with this product, he is advised to

immediately return this kit in new and unused condition to the place of purchase for a full refund.

Assembly Instructions

Herr Engineering Corp.

Award Winning Model Designs

A Division of SIG Mfg. Co., Inc.

P.O. Box 520   •   Montezuma, Iowa  50171-0520

Phone: (641)623-5154   •   Website: www.iflyherr.com

Summary of Contents for HRR506










Reviews: