GB
- 16 -
•
Adjust the spark deflector (3) periodically to
compensate for wear on the wheel.
5.3 Assembling the workpiece supports (Fig.
6)
Screw the workpiece supports (7) to the double
wheel grinder using the star screw (6) and the
assembly screws (12).
5.4 Adjusting the workpiece supports
(Fig. 7 / Item 7)
•
Adjust the workpiece supports (7) using the
fastening screws (6) so that the distance
between the dry grinding wheel (5) and the
workpiece support (7) is as small as possible
and certainly does not exceed 2 mm.
•
Adjust the workpiece supports (7) periodically
to compensate for wear on the dry grinding
wheel.
5.5 Changing the grinding wheel (Figs. 8-9)
Remove the 3 screws (A) holding the side section
of the safety hood (B) and remove the safety
hood. Undo the nut (D)
(Caution! The left grin-
ding wheel is fastened with a left-handed
thread and the right grinding wheel with a
right-handed thread)
, by holding the nut of
the grinding wheel mount on the opposite side.
Remove the
fl
ange (C). and replace the grinding
wheel (5). The grinding wheel is mounted with
the help of a rag. Mount the
fl
ange (C) on the
shaft and screw on the nut (D) hand-tight. To tigh-
ten the nut (D), hold the grinding wheel (5) with
a rag and tighten the nut (D). The guard hood (4)
must then be
fi
tted on again using the 3 screws
(A).
6. Operation
6.1 ON/OFF switch (1)
To switch on the equipment set the On/O
ff
switch
(1) to position 1.
Move the ON/OFF switch (1) to position 0 to
switch o
ff
the equipment.
After switching on the equipment wait for the
equipment to reach its maximum speed of rotati-
on before commencing with the sanding/grinding
work.
6.2 Grinding
•
We recommend that you use the fine-grained
grinding wheel for fine sanding/grinding work
and the coarse-grained grinding wheel for
coarse sanding/grinding work.
•
Place the workpiece onto the workpiece
support (7) and slowly guide the workpiece
towards the grinding wheel (5) at the desired
angle to the point where workpiece and grin-
ding wheel make contact.
•
Move the workspiece slightly back and forth
to produce an optimal grinding result. This
way the grinding wheel (5) is evenly worn.
Allow the workpiece cool every now and then.
Caution!
If the grinding wheel becomes jammed during
operation, remove the workpiece and wait until
the tool reaches its top speed again.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
Anl_H_DS_200_SPK7.indb 16
Anl_H_DS_200_SPK7.indb 16
13.09.2016 07:49:02
13.09.2016 07:49:02
