background image

 

 
               INSTALLATION, OPERATION AND MAINTENANCE MANUAL 
         
                        A1584 5 AMP POWER SUPPLY (TERMINAL VERSION) 

 

 

 

Contents                                                                                           Page                                                       
 
1.   Introduction                                                                                  1   
2.   Warnings                                                                                       2 
3.   General Description                                                                      3  
4.  Specification                                                                                  5 
5.  Terminations List                                                                         5       
6.  Adjustments and Indications                                                      6 
7.  Installation Procedure                                                                 7    
8.  Commissioning                                                                             8 
 
 
 
 
1.  Introduction 

 

Thank you for purchasing this 5A Power Supply Unit. This power supply is designed 
to the requirements of EN54-4. This power supply will provide the user with many 
years of reliable service. 

  
 
NOTE: It is important to read this manual before commencing installation. 

Document Ref: O&M15845T.DOC/Rev 0  16.11.99    Page 1 of 8  Originator KP  Checked AP   Approved JBJ 

Summary of Contents for A1584









Reviews: