background image

 Important: Always read and follow instructions. 

• iii

Table of Contents

Important Safety Instructions .................................ii

Owner’s Responsibility .............................................. iv
Operator Protective Equipment ................................. iv
Definitions of Hazard Levels ...................................... iv
Symbols Used ........................................................... iv

Installation Instructions ...........................................1

Information on Pre-installation Location .....................1
Assembly Case for Floor Level Installation ................2
Evenness of The Measuring Unit ...............................2
Network Environment ................................................2
Special Accessories ....................................................2
Electrics ......................................................................2
Measurement Bay ......................................................3
Set-up Tread Scanner and Camera .............................4
Installation Tread Scanner on Floor .............................5
Size .............................................................................6
Foundation Layout ......................................................7
Floor Levelness and Central Unit ...............................9

Checklist .................................................................. 10

Summary of Contents for COATS Tread Scanner

















Reviews: