manualshive.com logo in svg

Hella AF 100 K, Technical Documentation Manual

Share
Download
Hella AF 100 K Technical Documentation Manual Download Page 7

Gear Blind OS 58/56

Subject to technical modifi cations - Date 06/2006

3

Type: AF 50

Tender Specifi cation and Limit Sizes

Top Rail

U-shaped moulded cold roll profi le, galvanised and borde-
red on both edges; dimensions 58 x 56 mm. (Cutting edges 
without surface treatment.)
For a surcharge, top rail with extruded aluminium, dimensions 
59 x 59.5 mm, if requested. 
Installation with galvanised steel brackets and integrated 
fi xing devices for cover to discreetly hide the clamps of the 
protection cover. 

Bottom Rail

Extruded, closed aluminium profi le, powder-coated or natural-
ly anodised. Dimensions 50 x 18.6 mm.
Closed with plastic end caps. 

Slats

Slightly curved aluminium slats made from highly elastic 
special alloy, bend proof, scratchproof and shockproof, 2-layer 
stove enamelled (incl. on the longitudinal edges); slat width 
50 mm, slat thickness 0.24 mm. 

Slat Guide (Wind Protection Device) 

Standard: low-noise stable wire tension system made from 
braided fl at tape, UV-protected, dimensions 4.5 x 1.5 mm. For 
a surcharge, alternative: wire tension, polyamide-coated steel 
cord, polyamide-coated stainless steel cord or shiny stain-
less steel cord. All variations dimensions: ø 3 mm. Punched 
through the ends of all the slats, stretched taught using a wire 
bracket of die-cast aluminium with nipple. 

Tilting Device

Standard: Tilting device without a working position tilting 
both ways. When lowering the blind, it is closed towards the 
exterior, smooth tilting process when changing direction of 
movement, when raising the blind, it is closed towards the 
interior. 
For a surcharge (if requested, or standard at AF 50L): Variotec-
bearing with working position. Blind lowers in the shading 
position (approx. 50°), when it reaches the bottom end posi-
tion the blind closes completely, smooth tilting process when 
changing direction of movement, blind raises in the horizontal 
position. (Adjustable and lockable with a short upward motion 
at any height).

Ladder Cord 

High-strength shrink-resistant terylene-polyester. 
For a surcharge with transverse tensioning, joined to every 
slat non-positively (double Omega-punching), if requested. 

Lifting Tape

Anti-friction coated lifting tapes for a run with minimum wear 
and tear and maximum UV-protection, dimensions 6.0 x 0.28 
mm, tear-proof at 750N, guaranteed thickness tolerance in the 
range of 1/100 mm. 

Crank Handle Operation

Raising and lowering the blind and repositioning the slats 
using a crank handle. Maintenance-free bevel gear unit with 
gear reduction 2:1, duct into the interior via bearing, powder-
coated aluminium crank rod with folding handle and crank 
holder. For a surcharge, end stops at the top and bottom via 
limit stop.

Electric Operation

Raising and lowering the blind and repositioning the slats 
using an electric motor (230 V/AC). Drive with integrated 
planetary gear, end switch at the top and bottom, thermo-pro-
tection switch to prevent overloading the motor. Tilting of the 
slats is enabled by lightly touching the switch in the respec-
tive direction. If several motors should be activated with one 
switch, a control unit is necessary.

Protection Cover, Half-box, Whole-Box

Technical description in the tender specifi cation “Covers”. 

(EIGHTåOFå"LIND

(EIGHTåOFåPACKAGE (EIGHTåOFåCOVER

(EIGHTåOFå"LIND

(EIGHTåOFåPACKAGE (EIGHTåOFåCOVER

;MM=

;MM=

;MM=

;MM=

;MM=

;MM=

-ODEL

MAXå(EIGHT MAXå3URFACE MAXå3URFACE

-ANUALåOPERATION

WITHOUTåLIMITåSTOP

WITHåLIMITåSTOP

;MM=

;MM=

;MÁ=

!&åå+

!&åå+

-OTORISEDåOPERATION

3TANDARDå-OTOR

/BJECT

;MM=

;MM=

;MÁ=

!&åå-å%LERO 

!&åå-å%LERO

!&åå-å3OMFY 

!&åå-å3OMFY

å

ORåRATHERåATåBLINDåWITHåTILTINGåDEVICEåWITHåWORKINGåPOSITION
ASåREGARDS

A åMODELåWITHåWORKINGåPOSITION
B åMODELåWITHåLIGHTåCONTROLåFUNCTION

-INå7IDTHå

-OTOR

 

Ext

er

ior 

V

enetian Blind 

Summary of Contents for AF 100 K























































Reviews:

No comments

Brands by name

Popular brands

Load more brands