Specifications are subject to change without notice. No liability accepted for errors or omissions.
10
High performance
DC
UPS system
No
-
Break
switching between charger & battery
Battery detection
-
regular battery presence and
battery circuit integrity checks
Alarm relay outputs
LED flash codes for precise state indication
Deep discharge protection for batteries
ECB for battery overload & short circuit protection
Fused reverse battery polarity protection
Automatic temperature compensated output volts
Option
-
battery condition test (BCT)
Option
-
communication interface allows remote
monitoring & user control of BCT function
-
i
ver-
sions
Batteries external to charger
-
order separately
ENVIRONMENTAL
Operating
temperature
Storage temperature
Humidity
Cooling
Protection
♦
24 Month Warranty
Input voltage
Fusing / protection
Isolation
Efficiency
Inrush current
Output power
Output voltage
Voltage adj. range
Temp. compensation
Current limit
Line regulation
Load regulation
Noise
Drift
Hold
-
up time
Turn on time
Thermal protection
Overvoltage protection
EMI
Safety
Vibration
ELECTRICAL
180
-
264V, 50/60 Hz (standard)
or 88
-
132VAC (internal link selectable)
5A input fuse and varistor
Battery fuse plus ECB for battery circuit
1KV DC input
-
output / earth
> 85%
Soft start circuit
250W
13.8, 27.6, 34.5, 41.4, 55.2VDC
85
-
105% of Vout
Temperature sensor on 1.7m lead with adhe-
sive pad:
-
4mV / °C / cell ±10%
PSU:
100% rated current
Battery:
25
-
100% rated current (factory set)
<0.2% over AC input range
<0.4% open circuit to 100% load
<1% output voltage
0.03% / °C
20 ms without battery (nominal
-
max. Vin)
< 1 sec
Yes, self
-
resetting
Over
-
voltage protection on output
at ~ 130% of nominal output voltage
CISPR 22 / EN55022 class A
IEC950 / EN60950 / AS/NZS3260
Designed to meet MIL
-
STD
-
810F Method
514.5
-
20 to 50 °C ambient at full load
De
-
rate linearly at >50 °C to zero @ 70 °C
-
30 to 85 °C ambient
0
-
95% relative humidity non
-
condensing
Natural convection except for 12V model (fan)
IP20
No
-
Break
™ FUNCTIONS AND ALARMS
Reverse polarity pro-
tection
Battery monitoring
Battery protection
-
low battery volts
-
overload
-
short circuit
Indication LEDs
Alarms
Alarm relay contacts
Standby mode
Battery condition test
(BCT)
Battery reverse connection will open internal
fuse (and produce alarm)
Detects for presence of battery on start up,
then every 60 minutes when charge current <
200mA
Electronic circuit breaker (ECB) operates
under the following conditions:
•
battery voltage drops to 1.67V/cell
-
auto reset
•
< 300ms for load > 6 x rated PSU cur-
rent, allows ~1.5x rated PSU current
from battery without acting,
•
< 2ms, backed up by fuse
Green:
Battery System OK, Power OK
Red:
Standby
•
Power OK (alarm on mains fail)
•
Battery System OK
-
alarms when battery
voltage low (on mains fail) , battery
missing, battery circuit wiring faulty, BCT
fail (if enabled)
C
-
NO
-
NC full changeover rated 1A /50V
DC, 32VAC
Turns off DC output of PSU & allows load to
run off battery
Optional
-
if enabled, default setting =
20mins/28days). BCT can be started and
stopped by the user on SR250
i
.
BCT relay
provided to control an external test load.
incl. SR250
i
SPECIFICATIONS
All specifications are typical at nominal input, full load and at 20°C unless otherwise stated.
