Helion AURA 650 Instruction Manual Download Page 2

  2 / 14

Safety Precautions and Warnings

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS, THIS IS NOT A TOY

As the user of this product, you are solely responsible for operating in a manner that does not 

endanger yourself and others or result in damage to the product or the property of others.
 

▪ Always keep a safe distance around your model to avoid collisions or injury. This model is 

controlled by a radio signal subject to interference from many sources outside your control. Inter

-

ference can cause momentary loss of control.

▪ Always operate your model in open spaces away from full-size vehicles, traffic and people.
▪ Always follow the directions and warnings for this and any optional support equipment (chargers, 

rechargeable battery packs, etc.).
▪ Always avoid exposing the electronic parts of this model to water. Moisture causes damage to 

electronics.

▪ Never operate your model with low transmitter batteries.
▪ Always keep your model in sight and under control.
▪ Always use fully charged batteries.
▪ Always keep transmitter powered on while vehicle is powered.
▪ Always remove batteries before disassembly.
▪ Always keep moving parts clean.

Whether you’re an experienced RC skipper or new to the hobby, the Helion Aura 650 is the 

sailboat for you.  The Aura 650’s hull is made from durable blow-molded ABS for added 

strength and has an attractive pre-applied trim on both the hull and sail that lets it stand out on 

the water like a full-size sailboat.  It also comes pre-assembled and partially pre-rigged to help 

make it easy to get on the water.  Plus, the Aura is the ideal size for sailing on nearly any body 

of water and small enough to transport back and forth in either the back seat or trunk of your 

car.

The Aura 650 is a RTR boat, so everything you need to get started is included in the box - 

including a 2.4GHz radio system, a 17 gram “drum style” sail winch servo, and rip-stop nylon 

sails that provide durability and great performance.  Even the 8 AA batteries (4 for the transmit

-

ter and 4 to power the servos) that you need to operate the boat are included so you won’t 

have long to wait before you’re tacking your new Aura 650 across a local pond or lake!

MADE IN CHINA

Distributed in the UK by:

J Perkins Distribution Ltd,  

Lenham,  

Kent, UK   

ME17 2DL.  

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,   

Unit 1, 158-168 Browns Road,  

Noble Park,   

Victoria,  

3174,   

Australia. 

www.modelengines.com.au

 

Ph (03) 8793 5555   

[email protected]

Distributed in the US by:

Firelands Customer Service/Product Support   

1133 Libra Drive, Lincoln, NE 68512  

 

1-800-205-6773   

Introduction

Distributed and Serviced by:

Summary of Contents for AURA 650















Reviews: