Heitronic Rusty Installation And Operating Instructions Manual Download Page 8

Installations instructions Art. No. 36848

Page 2 of 2

Status 02.2009

Operation:

The solar light is ready assembled.

Place the solar light at the selected place by following the safety and warning notes.

Look for a suitable place with direct sun light when the unit is being charged up for the first time.

Make sure that the sun shines directly on the solar unit of the LED solar light. Shadows falling onto the
solar unit have a negative effect on the charging function of the rechargeable battery.

The solar LED light is charged up by the solar panel on the top. The day / night sensor switches it off
again during twilight. Make sure that the photo sensor at the top of the light is not influenced by other
light sources. The unit does not switch on during the twilight otherwise.

Make sure, after positioning, that the light is securely connected to the base. Watch during installation
out for possible places where people could stumble and trip up.

Make sure that the base and the fastening materials are suitable for supporting the weight of the light
permanently and reliably.

The LED solar light is put into service by operating the "AUTO" (see picture) on the lower side. The unit
is switched on automatically during the twilight. Slide the switch to the "OFF" position to switch of the
solar LED solar light.

The illuminant cannot be changed.

The solar light must be charged up over 2 sunny days for it to reach its optimum performance. The
lighting intensity can vary according to season of the year. More light will be shown if it has been a sunny
day than on a dull/overcast day.

The name plate must not be removed.

Changing the rechargeable battery:

Only use rechargeable batteries, type Ni-MH 1.2 V 500mA. The use of other rechargeable batteries can
lead to damage.

Detach the solar unit from the light (see picture).

Remove the old rechargeable batteries. Place the new rechargeable batteries into the battery
compartment. Make sure you have the right polarity for the rechargeable batteries. Reassemble the
parts in the reverse order.

Heitronic

®

H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein

Summary of Contents for Rusty









Reviews: