manualshive.com logo in svg

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual, Page: 29 / 250

Share
Download
HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 29

General information | Basic operation

3.8.2

Main menu of the user interface

1

2

Figure 3: User interface

1

Message display area, displays the time and the number of unclosed messages

2

Main menu with operating elements

Main menu operating elements

Operating element Function

3

Message

Display of an overview of all messages as well as the

number of messages that have not been closed

Further information:

 "Messages", Page 40

Measure

Positioning and measurement of minimum, maximum, and

range; perform relative measurements

Further information:

 "Measure menu", Page 30

File management

Management of the files that are available on the product

Further information:

 "File management menu", Page 31

User login

Login and logout of the user

Further information:

 "User login menu", Page 32

If a user with additional permissions (Setup

or OEM user type) is logged in, then the gear

symbols appears.

Settings

Settings of the product, such as setting up users, configuring

sensors, or updating the firmware

Further information:

 "Settings menu", Page 33

I

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

29

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Reviews:

No comments