4-11
&KDSWHU7528%/(6+227,1*
Symptom
&DXVH
Solution
Paper slips at the paper feed
section frequently.
The paper feed pressure
adjustment knob is set to “Thin
paper.”
Set the paper feed pressure
adjustment knob to “Thick paper.”
S
ĸ
The paper feed ring is dirty.
&OHDQLWZLWKDOFRKRO
S
The sheets of paper are sticking
to each other and cannot be
separated.
)DQWKHSDSHUZHOO
S
The paper is outside the
VSHFL¿FDWLRQV
Use paper that meets
VSHFL¿FDWLRQV
S
The side guides press
against the paper too tightly.
Set the side guides so that they
push against the paper lightly.
S
A trouble has occurred inside the
machine.
&DOO\RXUGHDOHU
Paper jams frequently.
The rubber roll is dirty.
&OHDQLWZLWKDOFRKRO
S
Paper shreds are stuck inside the
paper conveyance passage.
&KHFNLQVLGHWKHPDFKLQHDQG
remove any paper shreds.
The stacker rollers position is not
correct.
Adjust the position of the stacker
UROOHUV
S
The paper is curled.
Straighten the paper curl.
The guide plate unit is left attached
to the paper ejection plate.
5HPRYHWKHJXLGHSODWHXQLW
S
Static electricity has occurred in the
paper.
6SUD\DFRPPHUFLDOO\DYDLODEOHDLU
duster on the rubber roll.
Paper slips in the vertical direction.
After a paper type was changed,
a folding position has not been
adjusted.
&KHFNWKDWWKHURXJKDGMXVWPHQW
knob position is correct.
S
Paper slips in the horizontal
direction.
The paper is stacked unevenly.
Stack the paper neatly on the
paper feed table.
S
There is space between the paper
and side guide.
Set the side guides so that they
push against the paper lightly.
S
The rubber roll is deformed.
&DOO\RXUGHDOHU
Paper jam at the rubber roll when
thick paper or cross folded thick
paper is folded into two.
The paper is outside the
VSHFL¿FDWLRQV
Use paper that meets
VSHFL¿FDWLRQV
S
The space inside the internal paper
conveyance passage is narrow.
:LGHQWKHVSDFHXVLQJWKH¿QH
adjustment knob of the second
IROGLQJSODWH
S
Small paper is fed continuously
VWUHDPIHG
The paper is outside the
VSHFL¿FDWLRQV
Use paper that meets
VSHFL¿FDWLRQV
S
The paper feed pressure
adjustment knob is set to “Thick
paper.”
Set the paper feed pressure
adjustment knob to “Thin paper.”
S
ĺ
Summary of Contents for TF MEGA-M
