HeatStar HSU200NG Operating Instructions And Owner'S Manual Download Page 1

OPERATING INSTRUCTIONS 

AND OWNER’S MANUAL

MODEL#

HSU200NG
HSU250NG
HSU300NG
HSU400NG

READ INSTRUCTIONS CAREFULLY:

 

YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS. 

Read and follow all instructions. Place instructions in a safe place for future reference. Do not 
allow anyone who has not read these instructions to assemble, light, adjust or operate the 
heater.

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause 
injury or property damage. Refer to this manual. For assistance or additional information 
consult a qualified installer, service agency or the gas supplier.

-

WHAT TO DO IF YOU SMELL GAS

 

Ǟ

DO NOT try to light appliance.

 

Ǟ

DO NOT touch any electrical switch, do not use any phone in your building

 

Ǟ

Leave the building immediately

 

Ǟ

Immediately call your gas supplier from a phone remote from the building. Follow the gas 
suppliers instructions

 

Ǟ

If you cannot reach your gas supplier, call the Fire Department.

- Installation and service must be performed by a qualified installer, service agency or the gas 
supplier.

FOR YOUR SAFETY: 
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any 
other appliance.

WARNING:

 

If the information in these instructions are not followed exactly, a fire or explosion 

may result causing property damage, personal injury or loss of life.

LARGE UNIT HEATER

FOR RESIDENTIAL/COMMERCIAL USE

WWW.HEATSTARBYENERCO.COM

1-(866)-447-2197

 60266

Summary of Contents for HSU200NG





















































































Reviews: