background image

15

5.0 EXPLANATION TO USER 

The Multipoint SS unvented heater stores water at the temperature set on 

1. 

the adjustable control knob. This can be set to give temperatures in the 

range 10°C to 70°C. In hard water areas it is advised that the maximum 

temperature is restricted to prevent build up of scale. To avoid risk of 

freezing when the heater is not in use for long periods during the winter 

months, do not switch off the electrical supply and set the thermostat to 

its minimum position. N.B. This will not protect other system pipework.

The indicator lights will be illuminated when the unit is heating.

2. 

To ensure the heater continues to operate at its optimum performance 

3. 

it should be periodically maintained in accordance with the instructions 

given under the section headed MAINTENANCE.

IMPORTANT NOTES TO USER

DO NOT BLOCK OR RESTRICT THE DISCHARGE FROM ANY SAFETY 

• 

VALVE FITTED.

DO NOT TAMPER WITH ANY SAFETY VALVE FITTED.

• 

IF WATER DISCHARGES FROM ANY SAFETY VALVE FITTED SWITCH 

• 

OFF THE ELECTRICAL SUPPLY TO THE UNIT IMMEDIATELY. CONTACT 

THE HEATRAE SADIA SERVICE TEAM (TEL: 0844 8711530) OR AN 

APPROVED INSTALLER. DO NOT TURN THE ELECTRICAL SUPPLY 

ON AGAIN UNTIL THE UNIT HAS BEEN CHECKED AND APPROVED 

BY A QUALIFIED INSTALLER.

6.0 MAINTENANCE

WARNING: DISCONNECT FROM ALL ELECTRICAL SUPPLIES BEFORE 

BEGINNING ANY WORK ON THE MULTIPOINT SS. FLUID CONTAINED 

IN THE CYLINDER MAY BE VERY HOT!

To ensure the continued safe and efficient operation of the Multipoint SS it 

should be regularly maintained. 

Maintenance should be carried out by a competent person and any replacement 

parts used should be authorised Heatrae Sadia Multipoint SS spare parts. 

It is recommended that maintenance is carried out annually and should include 

the checks detailed in the sections on page 16 & 17.

Summary of Contents for MULTIPOINT 100

























Reviews: