background image

34922 Rev B

4

12-01

T4800 INSTALLATION INSTRUCTIONS

WARNING!

This fireplace and its components are designed to be installed and operated as a system. Any alteration to or

substitution for items in this system, unless allowed by these installation instructions, will void the Underwrit-

ers Laboratories listing and may void the product warranty. It may also create a hazardous installation. Read

through these instructions thoroughly before starting your installation and follow them carefully throughout

your project.

1. The Heatilator fireplace system consists of the following:

a.

Fireplace/Integral  Grate/Outside  Combustion Air  System

b.

Refractory

c.

Chimney  Termination  Cap

d.

Chimney  System

e.

Hearth  Extension

2. Optional Components Include:

a.

Glass  Doors

b.

Chimney Air Kit

NOTE: 

Illustrations used throughout these instructions

reflect  “typical  installations”  and  are  for  design  pur-

poses only. Actual installation may vary slightly due to

individual design preferences. However, minimum and

maximum clearances must be maintained at all times.
The  illustrations  and  diagrams  used  throughout  these

installations  instructions  are  not  drawn  to  scale.

Figure 1 - Typical Fireplace System

B. DESCRIPTION OF  THE  FIREPLACE SYSTEM

This  fireplace  system  has  been  tested  and  listed  in

accordance  with  UL  127  standards,  and  has  been  listed

by  Underwriters  Laboratories  Inc.  for  installation  and

operation in the United States as described in this manual.
This fireplace has been tested and listed for use with the

optional  components  listed  on  page  5.  These  optional

components  may  be  purchased  separately  and  installed

at a later date. However, installation of an outside air kit

will  require  significant  reconstruction,  and  should  be

installed at the time of the initial fireplace installation.

Check  with  your  local  building  code  agency  prior  to

installing  this  fireplace  to  ensure  compliance  with  local

codes,  including  the  need  for  permits  and  follow-up

inspections.  If  you  need  assistance  during  installation,

please contact your local dealer or the Heatilator Technical

Services Department, Hearth Technologies Inc., 1915 W.

Saunders St., Mt. Pleasant, Iowa 52641 (1-800-843-2848).

Heatilator®  is  a  registered  trademark  of  Hearth

Technologies Inc., Division, HON INDUSTRIES.

A. LISTINGS  AND CODE  APPROVALS

Summary of Contents for traditional T4800





























Reviews: