Heatilator NNXT3933IF-B Owner'S Manual Download Page 15

15

Heatilator  •  NNXT4236IF-B, NNXT4236ILF-B, NNXT3933IF-B, NNXT3933ILF- B Owner’s Manual  • 2384-981 Rev. G  •  6/18 

•  Clean glass with a non-abrasive commercially available 

cleaner.
-  Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass 

cleaner (consult with your dealer)

•  Carefully set fixed glass assembly in place on fireplace, 

ensuring it is centered in the opening. Hold glass in place 

with one hand and secure glass latches with the other 

hand.

•  Inspect and operate all glass latches to ensure they    

move freely and no obstructions are present.

•  Reinstall decorative front.

Decorative Fronts

Frequency: 

Annually

By:  

Homeowner

Tools needed

:  Protective gloves, stable work surface

•  Assess condition of screen and replace as necessary.  
•  Inspect for scratches, dents or other damage and repair 

as necessary.

 

Check that louvers are not blocked.

 

Vacuum and dust surfaces.

Remote Control

Frequency: 

Seasonally

By:  

Homeowner

Tools needed: 

 Replacement batteries and remote con-

trol instructions.
•  Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control 

operation instructions for proper calibration and setup 

procedure.

•  Place batteries as needed in remote transmitters and 

battery-powered receivers.

•  Place remote control out of reach of children.

If not using your fireplace for an extended period of time 

(summer months, vacations/trips, etc), to prevent unin-

tended operation:
•  Remove batteries from remote controls.
•  Unplug 6-volt adapter plug on IPI models.

Venting

Frequency: 

Seasonally

By:  

Homeowner

Tools needed: 

 Protective gloves and safety glasses.

•  Inspect  venting  and  termination  cap  for  blockage  or 

obstruction such plants, bird nests, leaves, snow, debris, 

etc.

•  Verify termination cap clearance to subsequent construc-

tion (building additions, decks, fences, or sheds).  

•  Inspect for corrosion or separation.

•  Verify weather stripping, sealing and flashing remains 

intact.

•  Inspect draft shield to verify it is not damaged or missing.

Summary of Contents for NNXT3933IF-B


























Reviews: