Heatilator GCBC36LE Installation Instructions Manual Download Page 10

12-97

10i

28887A

3.  Gas Pressure

On the standing pilot Gas Control Valve, a pressure tap is
included on the front face of the Valve.  The electronic Valve
includes an 1/8” NPT plugged tap on the top and bottom of the
Valve near the outlet to the main burner.  Pressure taps are
immediately upstream of the gas supply connection and acces-
sible for test gauge connection.

Table 2 shows optimum gas pressure information. 

Consult your local gas company for assistance in determining
the proper orifice for your altitude or refer to ANSI Z223.1-latest
edition, Appendix F.

4.  Gas Conversions

Natural or propane gas conversions necessary to meet the
application need to be made by a qualified technician using
Heatilator specified and approved parts.

In the event your appliance must be converted to use propane,
you must use a CKVP Conversion Kit.  To convert to use natur-
al, you must use a CKVN Conversion Kit.

CALIBER 36” and 42”

Inlet gas supply pressure (natural gas)

4.5 (min.)-7.0 (max.) in w.c.

Optimum manifold pressure (natural gas)     3.5 in. w.c.

Inlet gas supply pressure (LP gas)

11.0 (min.)-14.0 (max.) in w.c.

Optimum manifold pressure (LP gas)          10.5 in. w.c.

Input rate (natural gas)

30,000 BTU/hr

Input rate (propane gas)

28,000 BTU/hr

Decorative - Natural Gas Orifice size

.110 in/ 2.79 mm

Decorative - Propane Gas Orifice Size

.063 in/ 1.60 mm

Table 2

Gas Information for Electronic and Standing Pilot Units

Summary of Contents for GCBC36LE























Reviews: