background image

7056-153F • 20 August, 2018

4

Heatilator EcoChoice WS18

www.heatilator.com

B. Warranty Policy

AUSTRALIAN WARRANTY INFORMATION

Hearth & Home Technologies Inc 

(

HHT

)

352 Mountain House Road | Halifax, PA 17032 | (717-362-9080)

HHT extends the following manufacturer’s warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased 

from an HHT authorized dealer.

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the 

appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from 

defects in materials and workmanship at the time of manufacture. 

After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the 

applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully 

discharge all of its obligations under this manufacturer’s warranty by replacing the product itself or refunding the verifi ed purchase price 

of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty 

is subject to conditions, exclusions and limitations as described below.

Warranty coverage begins on the date of original purchase. In the case of new home construction, coverage under this manufacturer’s 

warranty begins on the date of fi rst occupancy of the dwelling or six months after the sale of the product by an independent, authorized 

HHT dealer/ distributor, whichever occurs earlier. The warranty period for this manufacturer’s warranty shall commence no later than 24 

months following the date of product shipment from HHT, regardless of the installation or occupancy date. The manufacturer’s warranty 

period for parts and labor for covered components is produced in the following table. 

The term “Limited Lifetime” in the table below is defi ned as: 20 years from the beginning date of warranty coverage for gas appliances, 

and 10 years from the beginning date of warranty coverage for wood, pellet and coal appliances. These time periods refl ect the 

minimum expected useful lives of the designated components under normal operating conditions.

Warranty Period

Hearth and Home Technologies Manufactured Appliances and Venting

Components Covered

Parts

Labor

Gas

Wood

Pellet

EPA

Wood

Coal

Electric

Venting

1 Year

X

X

X

X

X

X

X

All parts and material 

except as covered by 

Conditions, Exclusions, 

and Limitations listed

2 years

X

X

X

Igniters, electronic 

components, and glass

X

X

X

X

X

Factory-installed blowers

X

Molded refractory panels

3 years

X

Firepots and Burnpots

5 years

1 year

X

X

Castings and baffl es

7 years

3 years

X

X

X

Manifold tubes,

HHT chimney and 

termination

10 

years

1 year

X

Burners, logs and 

refractory

Limited 

Lifetime

3 years

X

X

X

X

X

Firebox and heat 

exchanger

90 Days

X

X

X

X

X

X

X

All replacement parts 

beyond warranty period

Summary of Contents for ECO CHOICE WS18-AU















































Reviews: