manualshive.com logo in svg

Heatilator ECO-ADV-WS18, Owner'S Manual Installation And Operation

Share
Download
Heatilator ECO-ADV-WS18 Owner'S Manual Installation And Operation Download Page 7

7056-138L • August 23, 2019

7

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

Model:

ECO-ADV-WS18 Wood Appliance

Laboratory:

Intertek

Report Number:

3198460

Type:

Listed Room Appliance, Solid Fuel 

Type

Standard:

UL1482 and ULC S627-00 and 

(UM) 84-HUD, Mobile Home 

Approved.

NOTICE:

 This installation must conform with local codes. In the absence of local codes you must comply with the 

UL1482, (UM) 84-HUD and NPFA211 in the U.S.A. and the ULC S627-00 and CAN/CSA-B365 Installation 

Codes in Canada.

The Heatilator ECO-CHOICE Wood Appliance meets the U.S. Environmental Protection Agency’s crib wood emission  

limits for wood appliances sold after May 15, 2015. 

This wood appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate 

this wood appliance in a manner inconsistent with operating instructions in this manual.

EPA Certification #:

777

EPA Certified Emissions:

2.6 grams per hour

*LHV Tested Efficiency:

80.4 %

**HHV Tested Efficiency:

74.4 %

***EPA BTU Output:

10,900 to 22,600 / hr.

****Peak BTU/Hour 

Output:

49,600

Vent Size:

6 inches

Firebox Size:

2.0 cubic feet

Maximum Wood Length:

18 inches

Ideal Wood Length:

16 inches

Fuel

Seasoned Cord Wood

* Weighted average LHV efficiency using Douglas Fir 

dimensional lumber and data collected during EPA 

emissions test.

**Weighted average HHV efficiency using Douglas 

Fir dimensional lumber and data collected during EPA 

emissions test.
***A range of BTU outputs based on EPA Default 

Efficiency and the burn rates from the low and high EPA 

tests, using Douglas Fir dimensional lumber.

****A peak BTU out of the appliance calculated using the 

maximum first hour burn rate from the High EPA Test and 

the BTU content of cord wood (8600) times the efficiency.

A. Appliance Certification

B. BTU & Efficiency Specifications

1 

Listing and Code Approvals

Summary of Contents for ECO-ADV-WS18















































Reviews:

No comments

Brands by name

Popular brands

Load more brands