background image

H-IM-79E                      JANUARY 2011              Part No. 25001401

Beacon II™ 

Refrigeration Systems

Installation and

Operation Manual

Replaces H-IM-79E (09/07)

Table of Contents

Beacon II™ Board Layout ........................................................ 3
Installation Tips ........................................................................ 4
Refrigerant Line Brazing ........................................................... 5
Power Supply ........................................................................... 5
Wiring ....................................................................................... 5
Multiple Evaporator Configuration ........................................... 6
Box Temperature Control Settings ........................................... 7
Leak Testing ............................................................................. 7
Refrigerant Charging  ............................................................... 7
Start-Up Operation .............................................................. 8-11
Operating Mode Display ......................................................... 11
Programming and Reviewing Settings and Changes  ....... 12-13
 

Program Review Button

 

Select Button

 

Enter Button

Monitoring Items .................................................................... 14
 

Monitor Button

 

Force Defrost Button

 

Force Service Button

 

Reset Time Button

 

Clear/Test Button

Locking The Beacon II Board ................................................. 15
Status Indicator LED ......................................................... 15-16
Low Ambient Operation ......................................................... 16
Pumpdown ........................................................................ 16-17
Defrost ............................................................................... 17-18
Alarms  ................................................................................... 18
Error Indicator ......................................................................... 19
Checking Operation of Expansion Valve ........................... 20-21
Power Failures ........................................................................ 21
Spare Sensor Terminals .......................................................... 21
Checking Sensors .................................................................. 21
Sensor Resistance/Temperature Table ................................... 22
System Defaults ..................................................................... 22
InterLink Replacement Parts List ........................................... 23
Operational Limits .................................................................. 23
Expansion Valve Capacity ...................................................... 24
Diagnostics ........................................................................ 24-27
Wiring Diagrams ................................................................ 28-33
Preventive Maintenance ......................................................... 34
Service Record .................................................................. 35-36

Summary of Contents for BEACON II H-IM-79E





































Reviews: