Call 1-877-744-3649 for assistance or email us at [email protected]
4
MC
Control Panel:
FIG. 3
C
F
G
H
L
B
D
J
E
K
I
A
OPERATING INSTRUCTIONS:
Using the Control Panel (See Fig. 3 Below):
Master Power (I/O) Switch (A):
• Push button A to turn infrared heater on. Ensure that the red power light
“B” above the Master Power Switch is on - this confirms that the unit is plugged
in. It will turn from red to green when the Master Power Switch is pushed.
Fan Button (C):
• This is a High and Low setting for the fan and the heater. Note that the fan will
only come on if the thermostat temperature is set above the room temperature.
• The fan light (D) denotes the Low fan setting and the fan light (E) denotes
the High setting.
Timer (F):
• If a timer is desired, push this button once for a 1 hour timer, twice for a 2
hour time, etc (up to 12 hours). The time will show on the digital readout
screen. To reset, keep pushing the Timer button (F) until it returns to your
desired time setting. (Note that the timer is approximate and extreme caution
is necessary when the infrared heater is left operating and unattended. Keep
children, invalids and and pets away from the unit when in use.)
Temperature Buttons - Increase (G) and Decrease (H):
• This infrared heater is equipped with a thermostat. Press the Temperature
Button (G) to increase the temperature. Press the Temperature Button (H) to
decrease the temperature. (The infrared heater and fan will only turn on if the
temperature setting is higher than the room temperature.)
The Temperature Digital Readout Screen (I):
• This screen shows the current setting of the thermostat in Celcius or
Fahrenheit degrees. See Button (L) to adjust the setting to C or F.
• Press on the “°C/°F” Button (L)on the control panel for 3 seconds and after
a short “ beep” sound, the displayer will show the real room temperature for
5 seconds
• This screen will turn off after 5 minutes if there is no temperature adjustments.
• The temperature light (J) indicates if the digital reading is in Fahrenheit
and the temperature light (K) indicates the digital reading is in Celcius
NOTE:
The fan will continue to work for several minutes when the heaters
turns off. This allows the infrared components inside the heater to cool
down.
Using the Remote Control:
NOTE: This Infrared Heater is manufactured with a special CHILD LOCK feature to
prevent children from operating the controls. The CHILD LOCK feature automatically
activates after the product has been turned ON for more than 8 seconds. Once the
child lock feature is active, simply press the CHILD LOCK function on the REMOTE
CONTROL (shown below) to unlock the controls and operate the remote as normal
OR press and hold the On/Off (I/O) button for 3 seconds on the heater Control Panel.
This heater includes a remote control. To operate the appliance using the
remote control, ensure the red power light “B” is on. Each remote control is
shipped with a plastic tab inserted into the battery chamber to prevent
damage and power loss. Pls remove by pulling on the tab out of the
chamber. (See Maintenance Section). See below for directions to use the
remote control:
NOTE:
If the Remote Control is misplaced, press the Master Power (I/O) on the
Control Panel for 3 seconds and the controls will unlock after a short “beep” sound.
Celcius / Fahrenheit Setting Button (T):
• Push the button (T) to change the heat readout settings.
Temperature Buttons - Increase (Q) and Decrease (P):
• This infrared heater is equipped with a thermostat. Press the Temperature
Button (Q) to increase the temperature. Press the Temperature Button (P) to
decrease the temperature. (The infrared heater and fan will only turn on if the
temperature setting is higher than the room temperature.)
ESO Button Energy Savings Option (U):
• Push this button (U) once to move the temperature setting easily to 68
degrees F (20 degrees C).
• Push the ESO Button (U) an additional time to release the appliance from
the Energy Savings Option.
NOTE:
Direct the remote control at the appliance from 1 to 5 meter
distance for the remote control to function properly. The remote control
receptor is located in the control panel (Fig 1)
NOTE:
For remote control battery replacement, use Lithium Cell CR2025 3V.
WAVE
HEAT
N
S
T
Q
U
O
P
R
Fan Button (S):
•
This is a High and Low
setting for the fan and
the heater. Note
that the fan will only
come on if the thermostat
temperature is set above
the room temperature.
On/Off Button (N):
•
Push button N to turn
infrared heater on.
Child Lock Feature (R):
• Please note that the heater
will automatically engage
the Child Lock feature
after 8 seconds.
•
Push this Child Lock
button (R) once to unlock
the control panel
functions and remote
control functions
OR
press
and hold the On/Off (I/O)
button for 3 seconds on the
heater Control Panel.
FIG. 4
