background image

Heat-N-Glo Fireplace

Models:

AT-Supreme

Patents Pending

Installers Guide

WARNING: IMPROPER

INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE

INJURY OR PROPERTY DAMAGE.

REFER TO THIS MANUAL. FOR

ASSISTANCE OR ADDITIONAL

INFORMATION CONSULT A

QUALIFIED INSTALLER, SERVICE

AGENCY, OR THE GAS SUPPLIER.

Underwriters Laboratories Listed

438-982-A 12/97

READ THIS MANUAL BEFORE

INSTALLING OR OPERATING THIS

APPLIANCE. THIS 

INSTALLERS GUIDE

MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.

1.

This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home, where

not prohibited by local codes.

2. This appliance is only for use with the

type of gas indicated on the rating

plate. This appliance is not convertible

for use with other gases, unless a

certified kit is used.

Please contact your Heat-N-Glo Fireplace dealer for any

questions or concerns.  For the number of your nearest

Heat-N-Glo dealer, please call 612-890-8367.

Printed in U.S.A.

Copyright 1997,

Heat-N-Glo Fireplace Products, Inc.

6665 West Highway 13, Savage, MN 55378

- Do not store or  use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

-

What to do if you smell gas

• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier

from a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

- Installation and service must be

performed by a qualified installer,

service agency, or the gas supplier.

WARNING

IF THE INFORMATION IN

THESE INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE

OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE,

PERSONAL INJURY OR DEATH.

Summary of Contents for AT-Supreme
























Reviews: