background image

Harman®  •  Absolute43-C Owner’s Manual_R8  •  2018 -___  •  05/20

2

3-90-00772C

Congratulations

, The Harman

®

 Absolute43-C pellet stove 

you have selected is designed to provide the utmost in safety, 

reliability, and efficiency.
As the owner of a new pellet stove, you’ll want to read and 

carefully follow all of the instructions contained in this owner’s 

manual. Pay special attention to all cautions and warnings.

This owner’s manual

 

should be retained for future reference. 

We suggest that you keep it with your other important 

documents and product manuals.
Your new Harman

®

 Absolute43-C Freestanding Pellet Stove 

will give you years of durable use and trouble-free enjoyment. 

Welcome to the Harman

®

 family!

Harman

®

 is a registered trademark of Hearth & Home 

Technologies.

Note: Cast iron is an artisan crafted material, which is 

made the same way today as nearly 2000 years ago. 

Due to the intrinsic primitive nature of the casting 

process, part to part variation is normal and adds to the 

character of a hand built cast iron appliance

Read this manual before operating this appliance. 

Please retain this Owner’s Manual for future reference.

Read the Installation Manual before making any installation or finishing changes.

Listing Label Information/Location

The model information regarding your specific stove can be found on the 

rating plate usually located in the control area of the stove.

BARCODE LABEL

HF

Serial No.

N

o

 de série:

MODEL / MODÈLE: “Absolute43-C”

Room Heater Pellet Fuel-Burning Type

SUITABLE FOR MOBILE-HOME INSTALLATION

This pellet burning appliance has been tested and listed for use In

Manufactured Homes In accordance with OAR 814-23-900 through 814-23-909

352 Mountain House Road, Halifax, PA 17032    (É.-U.)

THIS AREA MUST 

BE BLACK

MINIMUM CLEARANCES TO

COMBUSTIBLES

Back Wall to Appliance 

2”

Side Wall to Appliance 

6"

Corner Installation

Walls to Appliance 

6.25”

Use  a  non-combustible  floor  protector 

extending under and to the sides, front 

and  back  of  the  unit  as  shown  in  floor 

protection diagram. Measure front 

distance from the surface of the glass 

door.

Recommended: Non-combustible floor 

protection  extended  beneath  the  flue 

pipe when installed with horizontal 

venting.
Floor Protection*

 

USA 

CANADA

Sides  (A)  6” 

152 mm

Back  (B)  1” 

25 mm

Front  (C)  6” 

152 mm

Alcove Installation

Min. Alcove Height  42” (1067mm)

Max. Alcove Depth  24” (610mm)

Report / Rapport

 #0135PS039E, 0135PS032S

Test to/testé à ASTM E 1509-12, ULC-S627-00, 

ASTM E 2515-11, ASTM E 2779-10

Room Heater, Pellet Fuel-Burning Type, Also For 

Use In Mobile Homes. (UM) 84-HUD

“PREVENT HOUSE FIRES”

 Install and use only 

in accordance with manufactures installation and 

operation instructions.

Contact  local  building  or  fire  officials  about 

restrictions and installation inspection in your area.

WARNING: FOR MANUFACTURED HOMES:

 

Do not install appliance in a sleeping room. An 

outside combustion air inlet must be provided. The 

structural integrity of the manufactured home floor, 

ceiling and walls must be maintained.

Refer to manufacturer’s instructions and local 

codes for precautions required for passing chimney 

through a combustible wall or ceiling. Inspect 

and clean exhaust venting system frequently in 

accordance with manufacturer’s instructions.

Use a 3” or 4” diameter type “L” or “PL” venting 

system.

Do not connect this unit to a chimney flue servicing 

another appliance.

Do not obstruct the space beneath the heater.

FOR USE WITH PELLETIZED WOOD FUEL ONLY.

EPA Certified Emissions: .99 g/hr

Input Rating Max:

 5.0 lb. fuel/hr

Electrical Rating:

 240 VAC, 50 Hz, Start 1.75 

AMPS, Run 1.25 AMPS

U.S. Electrical Rating:

 115 VAC, 60 Hz, Start 3.5 

AMPS, Run 2.5 AMPS

Fuel Type: 

Wood Pellet ONLY

Route power cord away from unit.

Modèle: “Absolute43-C”

Appareil de chauffage à granulés de bois

CONÇU POUR MAISONS MOBILES

3-90-7772_R1

OPERATE ONLY WITH DOORS CLOSED
DANGER

: Risk of electrical shock. Disconnect power supply before servicing.

Replace glass only with 5mm ceramic available from your dealer.
For further instruction refer to owner’s manual.
Keep viewing and ash removal doors tightly closed during operation.

DANGER:

 Risque d’électrocution. Coupez l’alimentation 

électrique avant l’entretien. 

Remplacer le verre avec 5 mm miroir verre céramique de la 

même qualité disponible auprès de votre revendeur. 

En tenant la porte d’entrée et le couvercle de la trémie 

hermétiquement fermé pendant le fonctionnement de 

l’appareil

DISTANCES DE SECURITE PAR RAPPORT AUX 

MATERIAUX COMBUSTIBLES

Paroi arrière à l’appareil 

51 mm

paroi latérale de l’appareil 

152 mm

Installation en angle

Entre murs et apparell 

159 mm

I

nstallation en alcôve

Hauter minimale de l’alcôve 

1067 mm

Profondeur maximale de l’alcôve  610 mm

PROTECTION DU SOL*

Côtés  (A)  152 mm

Arrière (B)  25 mm

Avant  (C)  152 mm
Utiliser une protection de sol non combustible sous l’appereil 

qui s’étend sur les côtes, l’avant et l’arrière du poêle (voir 

schéma). Pour la distance à l’avant, mesurer à partir de la 

surface de la porte en verre.
ll est recommendé que la protection s’étende jusque sous le 

conduit en cas d’installation d’un conduit horizontal ou sous 

le té en cas conduit vertical.

Do not remove this label/Ne pas enlever cette étiquette.

Made in the USA/Fabriqué aux É.-U.

Test pour / tested à la norme ASTM E 1509-12, ULC-S627-00, 

ASTM E 2515-11, ASTM E 2779-10

Chauffe-chambre, Pellet à combustibles Type, également pour les 

maisons mobiles. (UM) 84-HUD

"Empêcher MAISON incendies"

 Installer et utiliser uniquement 

en conformité avec les instructions du fabricant d'installation et 

d'exploitation.

Contactez le service des incendies à propos des restrictions et 

l'inspection d'installation dans votre région.

A

VERTISSEMENT: POUR maisons préfabriquées:

 Ne pas 

installer l'appareil dans une chambre à coucher. Une entrée d'air 

de combustion à l'extérieur doit être fournie. L'intégrité structurale 

de la maison étage, plafond et murs fabriqués doit être maintenue.

Reportez-vous aux instructions du fabricant et les codes locaux 

pour les précautions nécessaires pour faire passer la cheminée à 

travers un mur ou un plafond combustible. Inspectez et nettoyez 

système d'évacuation souvent en conformité avec les instructions 

du fabricant.

Utilisez un "ou 4" Type de diamètre «L» 3 ou le système de 

ventilation "PL".

Ne pas connecter cet appareil à un conduit de cheminée 

desservant un autre appareil.

Ne pas obstruer l'espace sous le chauffe-eau.

À UTILISER AVEC LA GRANULE DE BOIS SEULEMENT.

Émissions certifiés EPA: ,99 g / h

Entrée Max Note:

 £ 5,0 carburant / h

Note électrique:

 240 VAC, 50 Hz, Lancer 1,75 AMPS, Exécuter 

1,25 AMPS

US Note électrique:

 115 VAC, 60 Hz, 3,5 AMPS Démarrer, 

Exécuter 2,5 AMPS

Type de carburant: Bois Pellet SEULEMENT

Route cordon électrique de l'appareil.

Fonctionner uniquement avec les portes fermées

Ce poêle à bois a besoin d’une inspection et d’une réparation 

périodiques pour fonctionner correctement. Consultez le manuel 

du propriétaire pour plus d’informations. Il est contraire à la 

réglementation fédérale d’utiliser ce poêle à bois d’une manière 

non conforme aux instructions d’utilisation du manuel du 

propriétaire.

Date of Manufacture / Date de fabrication:

2018   2019   2020   JAN   FEB   MAR   APR   MAY   JUN   JUL   AUG   SEP   OCT   NOV   DEC

Manufactured by / Fabriqué par: Hearth and Home Technologies 352 Mountain House Road, Halifax PA 17032

LABEL TICKET

ECO:

87270

LABEL SIZE:

5.75” H x 13.562” W

PART # / REV:

3-90-7772_R1

ADHESIVE:

ORIGINATOR:

Spidlet

MATERIAL:

24 Gauge Aluminum

DATE:

06/05/18

INK:

Black Background

(1) Holes = Ø.30

(5) Slotted Holes = .156 x .25

(4) Corners = R.062

Barcode label must have the serial number on it.

The barcode label must be able to read Code 39 Full ASCII.

352 Mountain House Road

Halifax, PA 17032

6"

2"

6.25"

6.25"

A

C

B

US ENVIRONMENTAL PROTECTION AGENCY

The  Absolute43-C is Certified to comply with 2020 particulate 

emission standards. 

L’Absolute43-C est certifié conforme aux normes d’émission de 

particules de 2020.

This wood heater needs periodic inspection and repair for proper operation. 

Consult the owner’s manual for further information. It is against federal regulations 

to operate this wood heater in a manner inconsistent with the operating instructions 

in the owner’s manual.

Model Name

Serial Number

EXAMPLE

Summary of Contents for HARMAN Absolute43-C



























Reviews: