Hearth & Home Technologies • Wi-Fi Module Installation Instructions & User Guide • 2326-984 Rev. C • 7/20
2
6. Once steps 2 thru 5 are complete, your IFT-ECM
/ IFT-WFM is ready to be set up with the IntelliFire
app.
4. Connect the IFT-WFM to the IFT-ECM by aligning the
pins and tabs and pushing the IFT-WFM into the IFT-
ECM until both tabs snap into position. Ensure the two
components are fastened securely to one another.
See Figure 3.
3. Locate the IFT-WFM port on the end of the IFT-ECM.
Remove and discard the rubber cover from the IFT-
WFM port. See Figure 2.
5. Move the selector switch on the IFT-ECM back to
‘Remote’ position. The IFT-ECM will beep and display
three green LED flashes. On the IFT-ECM, locate the
‘PILOT’ button then press and hold for ten seconds.
The IFT-ECM will emit one audible beep for four
seconds. Release the ‘PILOT’ button. The IFT-WFM
green LED will flash every two seconds, indicating it
has an open access point. You can confirm the open
access point by seeing the IntelliFire_XXXX network
in the available Wi-Fi networks on your smart device.
Note:
The IFT-RFM is still required for use with a
remote to enable the thermostat function. The room
temperature is measured by a sensor in the IFT-
RC150 and/or IFT-RC400 remote control. Without a
paired remote, the TEMP function in the app will not
function correctly.
Figure 3 Connect Wi-Fi Module (IFT-WFM) to IFT-ECM
‘OFF’ POSITION
‘OFF’ POSITION
PAIRING HOLE
IFT-WFM
IFT-ECM
(Wi-Fi MODULE)
IFT-RFM
IFT-WFM
LED
IFT-ACM
PILOT
Please contact your Hearth & Home Technologies
dealer with any questions or concerns.
For the location of your nearest
Hearth & Home Technologies dealer,
please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
FCC Warning
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Canadian DOC Notice
This digital apparatus does not exceed the (Class A/ Class
B) limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian
Department of Communications.
Canadian IC Notice
This device complies with RSS-210 of Industry and Science
Canada. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Caution:
The Federal Communications Commission warns that
changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to op-
erate the equipment.
FCC Compliance Statement:
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, includ-
ing interference that may cause undesired operation of the
device.
