background image

Hearth & Home Technologies • GFK-160VF Fan Kit Installation Instructions • 4136-920 • Rev C • 8/22

4

Figure 14

Installing Air Deflectors
1.  Air Deflector orientation is critical to proper installation.  

With Air Deflector positioned properly, attach magnet as 

shown.  See Figure 14.  

2.  Bend mounting tab as show in Figure 14.

Figure 16

3.  Position the wide end of the Air Deflector into the third 

slot of Firebox Top, magnet should be facing up.  See 

Figure 16.

Figure 17

4.  Slide Air Deflector to the first slot and rotate up 90°.  Se

-

cure with (1) screw provided.  See Figures 17 & 18.

Figure 18

5.  Repeat steps 1 thru 4 for installation of the left Air De

-

flector.

Installing Speed Control
1.  Install the Speed Control in the lower right corner of the 

firebox or appliance, behind pull screen (if applicable).  

See Figure 19 and 20.

2.  Install Control Nut and Control Knob.

Figure 19 - (BUF/ACUF/IDOL)

Note:  When installed on the Idol series appliance, the Air 

Deflectors need to be shortened.  Break-off tabs are sup

-

plied to aide in the process.  The magnet is then placed at 

the end of the remaining deflector.  See Figure 15.

28 in. Idol

32 and 36in. Idol

Figure 15

Summary of Contents for GFK-160VF











Reviews: