manualshive.com logo in svg

HBM U5 Series, Mounting Instructions

Share
Download
HBM U5 Series Mounting Instructions Download Page 25

25

8.1

Dimensions mounting accessories for measurement of compressive/tensile torce

Compressive
force adapter

Measuring body U5

Tensile force
adapter

Measuring body U5

Screw DIN 912

Bearing plate

Screw DIN 912

Mounting accessory for measurement of compressive force (compressive force adapter)

Nominal force

∅

J

∅

H

K

L

M

Ball R

100kN

32

73.5

79

32

M12

160

200kN

32

95.5

95

42

M16

160

500kN

64.6

140

118

55

M20

400

Mounting accessory for measurement of tensile force (tensile force adapter)

Nominal force

K

 N

M

O

P

R

S

∅

T

∅

U

∅

Z

+0.1

100kN

74

M12

111

30

34

appr. 16

M30x2

164

34

200kN

96

M16

137

40

44

appr. 20

M39x2

190

43

500kN

138

M20

224.5

80

81.5

appr. 55

M72x4

260

76

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

SUNSTAR自动化 http://www.sensor-ic.com/ TEL: 0755-83376489 FAX:0755-83376182 E-MAIL:[email protected]

Summary of Contents for U5 Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands