The clear intuitive control panel helps you
quickly and easily turn on the heater and
warm milk, water or food for your baby.
Please, refer to the table from the instruction
for correct time mode.
CONTROL PANEL
BOTTLE
WARMING
INDICATOR
LIGHT
STANDBY
MODE
STERILISATION
FOOD AND
LIQUID HEATING
WARNING
• The device cannot be used by the individuals (including
children and old people) with physical disabilities, - they can
only use this device under the supervision of the people
responsible for their safety;
• DO NOT use metal (cutting or sharp) objects, that can leave
scratches on the device or on the power cable;
• DO NOT touch the switch or power cable with wet hands;
• Place the device on the flat horizontal surface while using it
and keep it childproof;
• DO NOT use the device near the sources of water or on wet
surfaces, where the device can get wet, to avoid electric
shock (including swimming pool);
• Water level should be minimum 1 cm below edges of the Warmer;
• Special conditions while transportation are not required.
MAINTAINING TEMPERTATURE
• Bottle warmer has a function of maintaining temperature. While in
warming mode this function controls temperature of water inside
the bottle warmer. After recommended warming time, the
temperature of the milk can rise above 36°-37°С. If you want to delay
the feeding, leave the bottle inside the warmer, putting the warmer
in the standby mode a little bit before recommended time. Then
temperature of the milk will be saved without loosing nutrients.
SAFETY MEASURES
• Check the integrity of the device and presence of all the details;
• Keep the inside plastic packing childproof, as it can be
dangerous for them;
• Before plugging the Bottle Warmer, make sure that:
1) Voltage corresponds to the technical characteristics of the device;
2) Socket should be grounded.
• Manufacturer is not responsible for consequences of ground
wire contact absence;
• If the power cord of the Warmer isn’t compatible with a
socket, appeal for a specialist. The use of supplementary
adapters and connectors is not recommended. If necessary,
use simple and multi-functional adapters, that corresponds to
the safety standards; DO NOT exceed the indicated voltage;
• In the case of the plug pin malfunction address to a specialist
and change it - thus you’ll be able to avoid an accident.
PRODUCT SPECIFICATION
15-30°C
50-80 %
HUMIDITY
WORKING TEMPERATURE
For domestic use only
FIELD OF APPLICATION
DEVICE
BOTTLE WARMER
50 Hz
220 W
340 ml
145×135×140 mm
100 cm
23002
220 V
LENGTH OF THE FLEX
SIZE
CONTAINER VOLUME
RATED POWER
RATED FREQUENCY
ITEM NUMBER
RATED VOLTAGE
290-330 ml
240-260 ml
180-210 ml
125-150 ml
90-110 ml
60-90 ml
MODE
CONTENT
5 min
7,5 min
3,5 min
4,5 min
6 min
9 min
4 min
5 min
8,5 min
13 min
5 min
6,5 min
11 min
19 min
5,5 min
8 min
14 min
24 min
7 min
11 min
5°C
20°C
5°C
20°C
FOOD AND LIQUID HEATING
BOTTLE WARMING
4,5 min
6 min
3 min
4 min
QUICK
WARMING
USAGE
/ FEEDING BOTTLES WARMING
• Put a bottle with milk or water in the Warmer bottom and pour water up to the level indicated on the inside of the bottle
(Picture 1,2)
.
Note:
1.
The water level should be minimum 1cm below the edge of the Warmer, even if the liquid level in a bottle is higher.
2.
Use filtered water, as tap or mineral water can provoke the scum formation.
3.
If you using HB
TM
bottle with removable handle, remove handle before placing bottle in the Warmer.
• Plug the device. Set
«Bottle Warming»
or
«Food and Liquid Heating»
mode, and indicator will light up
(Picture 3)
. It means that
the device began working. Choose mode according to the amount and temperature of the content (5° ‒ fridge temp., 20° ‒ room
temp.), paying attention to the time in which you going to start feeding. In the table below you’ll find approximate warming time
at different modes:
Note:
Indicator will sometimes fade out. This is normal: temperature control system is working.
Note:
1.
In table listed approximate time of liquid, warming to the human body temperature (36°-37°). Time can be different,
depending on various circumstances, like material of a bottle, water temperature and etc.
2.
After recommended warming time, the temperature of the milk can rise above 36°-37°С. If you want to delay the feeding,
leave the bottle inside the warmer, putting the warmer in the standby mode a little bit before recommended time.
Then temperature of the milk will be saved without loosing nutrients.
• Put the device on standby once the warming is complete
(Picture 4)
.
Note:
1.
It is recommended you start feeding the baby immediately after the milk has been warmed. Be sure to check the
temperature of the food before feeding
(Picture 5, 6)
.
2.
DO NOT place breast milk storage bags into the Warmer. It is advisable to pour breast milk from a bag into a bottle and
only then proceed to heating of the bottle with milk.
FOOD HEATING
• Pour filtered water in Warmer and then put a container with
baby food
(Pictures 7, 8)
.
Note:
Don’t pour in Warmer more than 160 ml of water!
Otherwise it may leak after putting the container.
• Plug the device.
• Set
«Food and Liquid Heating»
mode, and indicator will light up.
It means that the device began working
(Picture 9)
.
Note:
Indicator will sometimes fade out.
This is normal: temperature control system is working.
• Put the device on standby once the warming is complete
(Picture 10)
.
Note:
It is recommended you start feeding the baby immediately
after the milk has been warmed. Be sure to check the
temperature of the food before feeding.
STERILISATION
• Put a dummy or feeding bottle (disassembled) in the Warmer
(Picture 11)
. Pour filtered water
(Picture 12)
.
Note:
Make sure, that parts of the bottle would not be deformed at 100°C.
• Plug the device.
• Set
«Sterilisation»
mode, and indicator will light up. It means
that the device began working
(Picture 13)
.
Note:
1.
Sterilisation time depends on amount of water and objects
inside, and also on their cleanness, so prior cleaning is
highly recommended.
2.
Use filtered water, as tap or mineral water can provoke
the scum formation.
3.
Clean the inside of the Warmer before sterilisation. Put
bottles neck downwards - this position will ensure a
complete sterilisation. DO NOT take bottles with bare
hands immediately after the end of sterilisation, as it
will be heated to a very high temperature.
It is not recommended to use the Warmer to boil drinking water.
• Put the device on standby once the sterilisation is complete
(Picture 14)
.
