background image

Page 2

 

 

 

WARNING

 – Read and follow all instructions in this 

owner’s manual and on the equipment.  Failure to follow 

instructions can cause severe injury and/or death.

 

 
 

 

 

WARNING –

 

This product should be installed and serviced only by a qualified professional.

 

 

CAUTION –

 

All electrical wiring MUST be performed by a qualified electrical contractor, and must conform

to local electrical regulations and AS/NZS 3000 Wiring Rules.

 

 

Use of non-Hayward replacement parts voids warranty. 

 

ATTENTION INSTALLER – THIS MANUAL CONTAINS

 

IMPORTANT INFORMATION ABOUT THE 

INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER 

OF THIS PRODUCT.  FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS 

INJURY.

 

 

 

 

CAUTION

 – 

 

 

 

WARNING

 – 

 

 

 

WARNING

 – 

Pool and spa components have a finite life.  All components should be inspected frequently

and replaced at least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached.

 

 

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

This pump is intended for use on permanently installed swimming pools and may also be used

with hot tubs and spas if so marked. Do NOT use with storable pools. A permanently installed pool is constructed in

or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed

so that it is capable of being readily disassembled for storage and reassembled to its original integrity. Though this

product is designed for out door use, it is strongly advised to protect the electrical components from the weather.

Select a well-drained area, one that will not flood when it rains. It requires free circulation of air for cooling. Do not

install in a damp or non-ventilated location. If installed within an outer enclousere or beneath the skirt of a hot tub or 

spa, adequate ventilation and free circulation of air must be provided to prevent overheating of the motor.

IMPORTANT SAFETY INSTRUCTIONS

 

Before installing or servicing this electrical equipment, turn power supply OFF.   

 

 

 

WARNING 

 

Risk of Electric Shock.

 All electrical wiring must be performed by a

qualified electrical contractor, and must conform to electrical regulations and AS 3000 Wiring

Rules. All electrical circuits must be supplied through a Residual Current Device - RCD

(Safety Switch), with a residual operating current of 30mA. Hazardous voltage can shock, burn

and cause death or serious property damage. To reduce the risk of electric shock, do NOT use

an extension cord to connect unit to the electricity supply.

 

  

 

WARNING 

– 

To reduce the risk of electric shock replace damaged wiring immediately. Locate the power

cord to prevent abuse from lawn mowers, hedge trimmers and other equipment.

 

  

 

WARNING

 – 

Never operate the circulation system at more than (50PSI) 344Kpa maximum.

 

 

 

 

 

WARNING

 –

 

Automatic restart. 

The pump motor is automaticly protected from overload and overheating. 

If such an error occurs the controller will automaticly try to restart the pump. If a power failure occurs while the pump 

is running, it will automaticly restart once the power has been restored.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

TriStar Variable Speed Pump

30-LITINSB004 Rev-B

Summary of Contents for TriStar VS SP3215VS

















Reviews: