background image

IMPORTANT SAFETY INSTRUCTIONS

When using this electrical equipment, basic safety precautions should always be followed, including

the following:

READ AND FOLLOW ALL INSTRUCTIONS

 WARNING

 - Read and follow all instructions in this owner’s manual and on the equip-

ment. Failure to follow instructions can cause severe injury and/or death.

 WARNING

 - ELECTRIC SHOCK HAZARD. MOUNTING A LUMINAIRE THAT REQUIRES 

BONDING OR GROUNDING IN THIS NICHE CAN CAUSE SEVERE INJURY AND/OR DEATH. 

DO NOT MOUNT NON-UL LISTED LIGHTS OR ANY LUMINAIRE THAT REQUIRES BONDING 

OR GROUNDING IN THIS NICHE.

 WARNING

 - Risk of Electric Shock. Hazardous voltage can shock, burn, and cause 

death or serious property damage. All electrical wiring MUST be in conformance with ap-

plicable local codes, regulations, and the National Electrical Code (NEC). To reduce the risk 

of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide 

a properly located electrical receptacle. Before working on any electrical equipment, turn 

off power supply to the equipment.

 WARNING

 - Risk of Electric Shock. Opening light can cause shock, burn and severe 

injury. Light has no user serviceable parts inside. Do not open light.

 NOTICE

 - This swimming pool product is UL listed for permanently installed pools or 

spas only. It is not listed for storable pools or spas. Permanently installed pools and spas 

are those constructed in or partially in the ground and all others capable of holding water 

in a depth greater than 42 in (1.07 m). Storable pools and spas are those constructed on 

or above the ground and capable of holding water to a maximum of 42 in (1.07 m).

 WARNING

 - Electrical shock hazard. Damage to wiring can cause severe injury or 

death. To reduce the risk of electric shock replace damaged wiring immediately. Locate 

conduit to prevent abuse from lawn mowers, hedge trimmers and other equipment.

SAVE THESE INSTRUCTIONS

!

!

!

!

!

!

1

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Summary of Contents for Sheer 500

















Reviews: